[
  {
    "path": "MPU6050BasicExample.ino",
    "content": "/* MPU6050 Basic Example Code\n by: Kris Winer\n date: May 1, 2014\n license: Beerware - Use this code however you'd like. If you \n find it useful you can buy me a beer some time.\n \n Demonstrate  MPU-6050 basic functionality including initialization, accelerometer trimming, sleep mode functionality as well as\n parameterizing the register addresses. Added display functions to allow display to on breadboard monitor. \n No DMP use. We just want to get out the accelerations, temperature, and gyro readings.\n \n SDA and SCL should have external pull-up resistors (to 3.3V).\n 10k resistors worked for me. They should be on the breakout\n board.\n \n Hardware setup:\n MPU6050 Breakout --------- Arduino\n 3.3V --------------------- 3.3V\n SDA ----------------------- A4\n SCL ----------------------- A5\n GND ---------------------- GND\n \n  Note: The MPU6050 is an I2C sensor and uses the Arduino Wire library. \n Because the sensor is not 5V tolerant, we are using a 3.3 V 8 MHz Pro Mini or a 3.3 V Teensy 3.1.\n We have disabled the internal pull-ups used by the Wire library in the Wire.h/twi.c utility file.\n We are also using the 400 kHz fast I2C mode by setting the TWI_FREQ  to 400000L /twi.h utility file.\n */\n \n#include <Wire.h>\n#include <Adafruit_GFX.h>\n#include <Adafruit_PCD8544.h>\n\n// Using NOKIA 5110 monochrome 84 x 48 pixel display\n// pin 9 - Serial clock out (SCLK)\n// pin 8 - Serial data out (DIN)\n// pin 7 - Data/Command select (D/C)\n// pin 5 - LCD chip select (CS)\n// pin 6 - LCD reset (RST)\nAdafruit_PCD8544 display = Adafruit_PCD8544(9, 8, 7, 5, 6);\n\n// Define registers per MPU6050, Register Map and Descriptions, Rev 4.2, 08/19/2013 6 DOF Motion sensor fusion device\n// Invensense Inc., www.invensense.com\n// See also MPU-6050 Register Map and Descriptions, Revision 4.0, RM-MPU-6050A-00, 9/12/2012 for registers not listed in \n// above document; the MPU6050 and MPU-9150 are virtually identical but the latter has an on-board magnetic sensor\n//\n#define XGOFFS_TC        0x00 // Bit 7 PWR_MODE, bits 6:1 XG_OFFS_TC, bit 0 OTP_BNK_VLD                 \n#define YGOFFS_TC        0x01                                                                          \n#define ZGOFFS_TC        0x02\n#define X_FINE_GAIN      0x03 // [7:0] fine gain\n#define Y_FINE_GAIN      0x04\n#define Z_FINE_GAIN      0x05\n#define XA_OFFSET_H      0x06 // User-defined trim values for accelerometer\n#define XA_OFFSET_L_TC   0x07\n#define YA_OFFSET_H      0x08\n#define YA_OFFSET_L_TC   0x09\n#define ZA_OFFSET_H      0x0A\n#define ZA_OFFSET_L_TC   0x0B\n#define SELF_TEST_X      0x0D\n#define SELF_TEST_Y      0x0E    \n#define SELF_TEST_Z      0x0F\n#define SELF_TEST_A      0x10\n#define XG_OFFS_USRH     0x13  // User-defined trim values for gyroscope; supported in MPU-6050?\n#define XG_OFFS_USRL     0x14\n#define YG_OFFS_USRH     0x15\n#define YG_OFFS_USRL     0x16\n#define ZG_OFFS_USRH     0x17\n#define ZG_OFFS_USRL     0x18\n#define SMPLRT_DIV       0x19\n#define CONFIG           0x1A\n#define GYRO_CONFIG      0x1B\n#define ACCEL_CONFIG     0x1C\n#define FF_THR           0x1D  // Free-fall\n#define FF_DUR           0x1E  // Free-fall\n#define MOT_THR          0x1F  // Motion detection threshold bits [7:0]\n#define MOT_DUR          0x20  // Duration counter threshold for motion interrupt generation, 1 kHz rate, LSB = 1 ms\n#define ZMOT_THR         0x21  // Zero-motion detection threshold bits [7:0]\n#define ZRMOT_DUR        0x22  // Duration counter threshold for zero motion interrupt generation, 16 Hz rate, LSB = 64 ms\n#define FIFO_EN          0x23\n#define I2C_MST_CTRL     0x24   \n#define I2C_SLV0_ADDR    0x25\n#define I2C_SLV0_REG     0x26\n#define I2C_SLV0_CTRL    0x27\n#define I2C_SLV1_ADDR    0x28\n#define I2C_SLV1_REG     0x29\n#define I2C_SLV1_CTRL    0x2A\n#define I2C_SLV2_ADDR    0x2B\n#define I2C_SLV2_REG     0x2C\n#define I2C_SLV2_CTRL    0x2D\n#define I2C_SLV3_ADDR    0x2E\n#define I2C_SLV3_REG     0x2F\n#define I2C_SLV3_CTRL    0x30\n#define I2C_SLV4_ADDR    0x31\n#define I2C_SLV4_REG     0x32\n#define I2C_SLV4_DO      0x33\n#define I2C_SLV4_CTRL    0x34\n#define I2C_SLV4_DI      0x35\n#define I2C_MST_STATUS   0x36\n#define INT_PIN_CFG      0x37\n#define INT_ENABLE       0x38\n#define DMP_INT_STATUS   0x39  // Check DMP interrupt\n#define INT_STATUS       0x3A\n#define ACCEL_XOUT_H     0x3B\n#define ACCEL_XOUT_L     0x3C\n#define ACCEL_YOUT_H     0x3D\n#define ACCEL_YOUT_L     0x3E\n#define ACCEL_ZOUT_H     0x3F\n#define ACCEL_ZOUT_L     0x40\n#define TEMP_OUT_H       0x41\n#define TEMP_OUT_L       0x42\n#define GYRO_XOUT_H      0x43\n#define GYRO_XOUT_L      0x44\n#define GYRO_YOUT_H      0x45\n#define GYRO_YOUT_L      0x46\n#define GYRO_ZOUT_H      0x47\n#define GYRO_ZOUT_L      0x48\n#define EXT_SENS_DATA_00 0x49\n#define EXT_SENS_DATA_01 0x4A\n#define EXT_SENS_DATA_02 0x4B\n#define EXT_SENS_DATA_03 0x4C\n#define EXT_SENS_DATA_04 0x4D\n#define EXT_SENS_DATA_05 0x4E\n#define EXT_SENS_DATA_06 0x4F\n#define EXT_SENS_DATA_07 0x50\n#define EXT_SENS_DATA_08 0x51\n#define EXT_SENS_DATA_09 0x52\n#define EXT_SENS_DATA_10 0x53\n#define EXT_SENS_DATA_11 0x54\n#define EXT_SENS_DATA_12 0x55\n#define EXT_SENS_DATA_13 0x56\n#define EXT_SENS_DATA_14 0x57\n#define EXT_SENS_DATA_15 0x58\n#define EXT_SENS_DATA_16 0x59\n#define EXT_SENS_DATA_17 0x5A\n#define EXT_SENS_DATA_18 0x5B\n#define EXT_SENS_DATA_19 0x5C\n#define EXT_SENS_DATA_20 0x5D\n#define EXT_SENS_DATA_21 0x5E\n#define EXT_SENS_DATA_22 0x5F\n#define EXT_SENS_DATA_23 0x60\n#define MOT_DETECT_STATUS 0x61\n#define I2C_SLV0_DO      0x63\n#define I2C_SLV1_DO      0x64\n#define I2C_SLV2_DO      0x65\n#define I2C_SLV3_DO      0x66\n#define I2C_MST_DELAY_CTRL 0x67\n#define SIGNAL_PATH_RESET  0x68\n#define MOT_DETECT_CTRL   0x69\n#define USER_CTRL        0x6A  // Bit 7 enable DMP, bit 3 reset DMP\n#define PWR_MGMT_1       0x6B // Device defaults to the SLEEP mode\n#define PWR_MGMT_2       0x6C\n#define DMP_BANK         0x6D  // Activates a specific bank in the DMP\n#define DMP_RW_PNT       0x6E  // Set read/write pointer to a specific start address in specified DMP bank\n#define DMP_REG          0x6F  // Register in DMP from which to read or to which to write\n#define DMP_REG_1        0x70\n#define DMP_REG_2        0x71\n#define FIFO_COUNTH      0x72\n#define FIFO_COUNTL      0x73\n#define FIFO_R_W         0x74\n#define WHO_AM_I_MPU6050 0x75 // Should return 0x68\n\n// Using the GY-521 breakout board, I set ADO to 0 by grounding through a 4k7 resistor\n// Seven-bit device address is 110100 for ADO = 0 and 110101 for ADO = 1\n#define ADO 0\n#if ADO\n#define MPU6050_ADDRESS 0x69  // Device address when ADO = 1\n#else\n#define MPU6050_ADDRESS 0x68  // Device address when ADO = 0\n#endif\n\n// Set initial input parameters\nenum Ascale {\n  AFS_2G = 0,\n  AFS_4G,\n  AFS_8G,\n  AFS_16G\n};\n\nenum Gscale {\n  GFS_250DPS = 0,\n  GFS_500DPS,\n  GFS_1000DPS,\n  GFS_2000DPS\n};\n\n// Specify sensor full scale\nint Gscale = GFS_250DPS;\nint Ascale = AFS_2G;\nfloat aRes, gRes; // scale resolutions per LSB for the sensors\n  \n// Pin definitions\nint intPin = 12;  // This can be changed, 2 and 3 are the Arduinos ext int pins\n\nint16_t accelCount[3];           // Stores the 16-bit signed accelerometer sensor output\nfloat ax, ay, az;                // Stores the real accel value in g's\nint16_t gyroCount[3];            // Stores the 16-bit signed gyro sensor output\nfloat gyrox, gyroy, gyroz;                // Stores the real gyro value in degrees per seconds\nfloat gyroBias[3], accelBias[3]; // Bias corrections for gyro and accelerometer\nint16_t tempCount;               // Stores the internal chip temperature sensor output \nfloat temperature;               // Scaled temperature in degrees Celsius\nfloat SelfTest[6];               // Gyro and accelerometer self-test sensor output\nuint32_t count = 0;\n\nvoid setup()\n{\n  Wire.begin();\n  Serial.begin(38400);\n  \n  // Set up the interrupt pin, its set as active high, push-pull\n  pinMode(intPin, INPUT);\n  digitalWrite(intPin, LOW);\n  \n  display.begin();         // Initialize the display\n  display.setContrast(58); // Set the contrast\n  display.setRotation(2);  //  0 or 2) width = width, 1 or 3) width = height, swapped etc.\n\n  \n// Start device display with ID of sensor\n  display.clearDisplay();\n  display.setTextSize(2);\n  display.setCursor(20,0); display.print(\"MPU6050\");\n  display.setTextSize(1);\n  display.setCursor(0, 20); display.print(\"6-DOF 16-bit\");\n  display.setCursor(0, 30); display.print(\"motion sensor\");\n  display.setCursor(20,40); display.print(\"60 ug LSB\");\n  display.display();\n  delay(1000);\n\n// Set up for data display\n  display.setTextSize(1);      // Set text size to normal, 2 is twice normal etc.\n  display.setTextColor(BLACK); // Set pixel color; 1 on the monochrome screen\n  display.clearDisplay();      // clears the screen and buffer\n\n  // Read the WHO_AM_I register, this is a good test of communication\n  uint8_t c = readByte(MPU6050_ADDRESS, WHO_AM_I_MPU6050);  // Read WHO_AM_I register for MPU-6050\n  display.setCursor(20,0); display.print(\"MPU6050\");\n  display.setCursor(0,10); display.print(\"I AM\");\n  display.setCursor(0,20); display.print(c, HEX);  \n  display.setCursor(0,30); display.print(\"I Should Be\");\n  display.setCursor(0,40); display.print(0x68, HEX); \n  display.display();\n  delay(1000); \n\n  if (c == 0x68) // WHO_AM_I should always be 0x68\n  {  \n    Serial.println(\"MPU6050 is online...\");\n    \n    MPU6050SelfTest(SelfTest); // Start by performing self test and reporting values\n    Serial.print(\"x-axis self test: acceleration trim within : \"); Serial.print(SelfTest[0],1); Serial.println(\"% of factory value\");\n    Serial.print(\"y-axis self test: acceleration trim within : \"); Serial.print(SelfTest[1],1); Serial.println(\"% of factory value\");\n    Serial.print(\"z-axis self test: acceleration trim within : \"); Serial.print(SelfTest[2],1); Serial.println(\"% of factory value\");\n    Serial.print(\"x-axis self test: gyration trim within : \"); Serial.print(SelfTest[3],1); Serial.println(\"% of factory value\");\n    Serial.print(\"y-axis self test: gyration trim within : \"); Serial.print(SelfTest[4],1); Serial.println(\"% of factory value\");\n    Serial.print(\"z-axis self test: gyration trim within : \"); Serial.print(SelfTest[5],1); Serial.println(\"% of factory value\");\n\n    if(SelfTest[0] < 1.0f && SelfTest[1] < 1.0f && SelfTest[2] < 1.0f && SelfTest[3] < 1.0f && SelfTest[4] < 1.0f && SelfTest[5] < 1.0f) {\n    display.clearDisplay();\n    display.setCursor(0, 30); display.print(\"Pass Selftest!\");  \n    display.display();\n    delay(1000);\n  \n    calibrateMPU6050(gyroBias, accelBias); // Calibrate gyro and accelerometers, load biases in bias registers  \n    initMPU6050(); Serial.println(\"MPU6050 initialized for active data mode....\"); // Initialize device for active mode read of acclerometer, gyroscope, and temperature\n\n   }\n   else\n   {\n    Serial.print(\"Could not connect to MPU6050: 0x\");\n    Serial.println(c, HEX);\n    while(1) ; // Loop forever if communication doesn't happen\n   }\n\n  }\n}\n\nvoid loop()\n{  \n  // If data ready bit set, all data registers have new data\n  if(readByte(MPU6050_ADDRESS, INT_STATUS) & 0x01) {  // check if data ready interrupt\n\n    readAccelData(accelCount);  // Read the x/y/z adc values\n    getAres();\n    \n    // Now we'll calculate the accleration value into actual g's\n    ax = (float)accelCount[0]*aRes - accelBias[0];  // get actual g value, this depends on scale being set\n    ay = (float)accelCount[1]*aRes - accelBias[1];   \n    az = (float)accelCount[2]*aRes - accelBias[2];  \n   \n    readGyroData(gyroCount);  // Read the x/y/z adc values\n    getGres();\n \n    // Calculate the gyro value into actual degrees per second\n    gyrox = (float)gyroCount[0]*gRes - gyroBias[0];  // get actual gyro value, this depends on scale being set\n    gyroy = (float)gyroCount[1]*gRes - gyroBias[1];  \n    gyroz = (float)gyroCount[2]*gRes - gyroBias[2];   \n\n    tempCount = readTempData();  // Read the x/y/z adc values\n    temperature = ((float) tempCount) / 340. + 36.53; // Temperature in degrees Centigrade\n   }  \n   \n    uint32_t deltat = millis() - count;\n    if(deltat > 500) {\n \n    // Print acceleration values in milligs!\n    Serial.print(\"X-acceleration: \"); Serial.print(1000*ax); Serial.print(\" mg \"); \n    Serial.print(\"Y-acceleration: \"); Serial.print(1000*ay); Serial.print(\" mg \"); \n    Serial.print(\"Z-acceleration: \"); Serial.print(1000*az); Serial.println(\" mg\"); \n \n    // Print gyro values in degree/sec\n    Serial.print(\"X-gyro rate: \"); Serial.print(gyrox, 1); Serial.print(\" degrees/sec \"); \n    Serial.print(\"Y-gyro rate: \"); Serial.print(gyroy, 1); Serial.print(\" degrees/sec \"); \n    Serial.print(\"Z-gyro rate: \"); Serial.print(gyroz, 1); Serial.println(\" degrees/sec\"); \n    \n   // Print temperature in degrees Centigrade      \n    Serial.print(\"Temperature is \");  Serial.print(temperature, 2);  Serial.println(\" degrees C\"); // Print T values to tenths of s degree C\n    Serial.println(\"\");\n      \n    display.clearDisplay();\n     \n    display.setCursor(24, 0); display.print(\"MPU6050\");\n    display.setCursor(0, 8); display.print(\" x   y   z  \");\n\n    display.setCursor(0,  16); display.print((int16_t)(1000*ax)); \n    display.setCursor(24, 16); display.print((int16_t)(1000*ay)); \n    display.setCursor(48, 16); display.print((int16_t)(1000*az)); \n    display.setCursor(72, 16); display.print(\"mg\");\n    \n    display.setCursor(0,  24); display.print((int16_t)(gyrox)); \n    display.setCursor(24, 24); display.print((int16_t)(gyroy)); \n    display.setCursor(48, 24); display.print((int16_t)(gyroz)); \n    display.setCursor(66, 24); display.print(\"o/s\");     \n   \n    display.setCursor(0,  40); display.print(\"Gyro T  \"); \n    display.setCursor(50, 40); display.print(temperature, 1); display.print(\" C\");\n    display.display();\n    \n    count = millis();\n    }\n\n}\n\n//===================================================================================================================\n//====== Set of useful function to access acceleration, gyroscope, and temperature data\n//===================================================================================================================\n\nvoid getGres() {\n  switch (Gscale)\n  {\n \t// Possible gyro scales (and their register bit settings) are:\n\t// 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS  (11). \n    case GFS_250DPS:\n          gRes = 250.0/32768.0;\n          break;\n    case GFS_500DPS:\n          gRes = 500.0/32768.0;\n          break;\n    case GFS_1000DPS:\n          gRes = 1000.0/32768.0;\n          break;\n    case GFS_2000DPS:\n          gRes = 2000.0/32768.0;\n          break;\n  }\n}\n\nvoid getAres() {\n  switch (Ascale)\n  {\n \t// Possible accelerometer scales (and their register bit settings) are:\n\t// 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs  (11). \n    case AFS_2G:\n          aRes = 2.0/32768.0;\n          break;\n    case AFS_4G:\n          aRes = 4.0/32768.0;\n          break;\n    case AFS_8G:\n          aRes = 8.0/32768.0;\n          break;\n    case AFS_16G:\n          aRes = 16.0/32768.0;\n          break;\n  }\n}\n\n\nvoid readAccelData(int16_t * destination)\n{\n  uint8_t rawData[6];  // x/y/z accel register data stored here\n  readBytes(MPU6050_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers into data array\n  destination[0] = (int16_t)((rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value\n  destination[1] = (int16_t)((rawData[2] << 8) | rawData[3]) ;  \n  destination[2] = (int16_t)((rawData[4] << 8) | rawData[5]) ; \n}\n\nvoid readGyroData(int16_t * destination)\n{\n  uint8_t rawData[6];  // x/y/z gyro register data stored here\n  readBytes(MPU6050_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers sequentially into data array\n  destination[0] = (int16_t)((rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value\n  destination[1] = (int16_t)((rawData[2] << 8) | rawData[3]) ;  \n  destination[2] = (int16_t)((rawData[4] << 8) | rawData[5]) ; \n}\n\nint16_t readTempData()\n{\n  uint8_t rawData[2];  // x/y/z gyro register data stored here\n  readBytes(MPU6050_ADDRESS, TEMP_OUT_H, 2, &rawData[0]);  // Read the two raw data registers sequentially into data array \n  return ((int16_t)rawData[0]) << 8 | rawData[1] ;  // Turn the MSB and LSB into a 16-bit value\n}\n\n\n\n// Configure the motion detection control for low power accelerometer mode\nvoid LowPowerAccelOnlyMPU6050()\n{\n\n// The sensor has a high-pass filter necessary to invoke to allow the sensor motion detection algorithms work properly\n// Motion detection occurs on free-fall (acceleration below a threshold for some time for all axes), motion (acceleration\n// above a threshold for some time on at least one axis), and zero-motion toggle (acceleration on each axis less than a \n// threshold for some time sets this flag, motion above the threshold turns it off). The high-pass filter takes gravity out\n// consideration for these threshold evaluations; otherwise, the flags would be set all the time!\n  \n  uint8_t c = readByte(MPU6050_ADDRESS, PWR_MGMT_1);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c & ~0x30); // Clear sleep and cycle bits [5:6]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c |  0x30); // Set sleep and cycle bits [5:6] to zero to make sure accelerometer is running\n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_2);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c & ~0x38); // Clear standby XA, YA, and ZA bits [3:5]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c |  0x00); // Set XA, YA, and ZA bits [3:5] to zero to make sure accelerometer is running\n    \n  c = readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x07); // Clear high-pass filter bits [2:0]\n// Set high-pass filter to 0) reset (disable), 1) 5 Hz, 2) 2.5 Hz, 3) 1.25 Hz, 4) 0.63 Hz, or 7) Hold\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG,  c | 0x00);  // Set ACCEL_HPF to 0; reset mode disbaling high-pass filter\n\n  c = readByte(MPU6050_ADDRESS, CONFIG);\n  writeByte(MPU6050_ADDRESS, CONFIG, c & ~0x07); // Clear low-pass filter bits [2:0]\n  writeByte(MPU6050_ADDRESS, CONFIG, c |  0x00);  // Set DLPD_CFG to 0; 260 Hz bandwidth, 1 kHz rate\n    \n  c = readByte(MPU6050_ADDRESS, INT_ENABLE);\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, c & ~0xFF);  // Clear all interrupts\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x40);  // Enable motion threshold (bits 5) interrupt only\n  \n// Motion detection interrupt requires the absolute value of any axis to lie above the detection threshold\n// for at least the counter duration\n  writeByte(MPU6050_ADDRESS, MOT_THR, 0x80); // Set motion detection to 0.256 g; LSB = 2 mg\n  writeByte(MPU6050_ADDRESS, MOT_DUR, 0x01); // Set motion detect duration to 1  ms; LSB is 1 ms @ 1 kHz rate\n  \n  delay (100);  // Add delay for accumulation of samples\n  \n  c = readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x07); // Clear high-pass filter bits [2:0]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c |  0x07);  // Set ACCEL_HPF to 7; hold the initial accleration value as a referance\n   \n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_2);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c & ~0xC7); // Clear standby XA, YA, and ZA bits [3:5] and LP_WAKE_CTRL bits [6:7]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c |  0x47); // Set wakeup frequency to 5 Hz, and disable XG, YG, and ZG gyros (bits [0:2])  \n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_1);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c & ~0x20); // Clear sleep and cycle bit 5\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c |  0x20); // Set cycle bit 5 to begin low power accelerometer motion interrupts\n\n}\n\n\nvoid initMPU6050()\n{  \n // Initialize MPU6050 device\n\n//  wake up device-don't need this here if using calibration function below\n//  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors \n//  delay(100); // Delay 100 ms for PLL to get established on x-axis gyro; should check for PLL ready interrupt  \n\n  // get stable time source\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x01);  // Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001\n\n // Configure Gyro and Accelerometer\n // Disable FSYNC and set accelerometer and gyro bandwidth to 44 and 42 Hz, respectively; \n // DLPF_CFG = bits 2:0 = 010; this sets the sample rate at 1 kHz for both\n  writeByte(MPU6050_ADDRESS, CONFIG, 0x03);  \n \n // Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV)\n  writeByte(MPU6050_ADDRESS, SMPLRT_DIV, 0x04);  // Use a 200 Hz sample rate \n \n // Set gyroscope full scale range\n // Range selects FS_SEL and AFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3\n  uint8_t c =  readByte(MPU6050_ADDRESS, GYRO_CONFIG);\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c & ~0xE0); // Clear self-test bits [7:5] \n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c & ~0x18); // Clear AFS bits [4:3]\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c | Gscale << 3); // Set full scale range for the gyro\n   \n // Set accelerometer configuration\n  c =  readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0xE0); // Clear self-test bits [7:5] \n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x18); // Clear AFS bits [4:3]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c | Ascale << 3); // Set full scale range for the accelerometer \n\n  // Configure Interrupts and Bypass Enable\n  // Set interrupt pin active high, push-pull, and clear on read of INT_STATUS, enable I2C_BYPASS_EN so additional chips \n  // can join the I2C bus and all can be controlled by the Arduino as master\n   writeByte(MPU6050_ADDRESS, INT_PIN_CFG, 0x02);    \n   writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x01);  // Enable data ready (bit 0) interrupt\n}\n\n\n// Function which accumulates gyro and accelerometer data after device initialization. It calculates the average\n// of the at-rest readings and then loads the resulting offsets into accelerometer and gyro bias registers.\nvoid calibrateMPU6050(float * dest1, float * dest2)\n{  \n  uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data\n  uint16_t ii, packet_count, fifo_count;\n  int32_t gyro_bias[3] = {0, 0, 0}, accel_bias[3] = {0, 0, 0};\n  \n// reset device, reset all registers, clear gyro and accelerometer bias registers\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device\n  delay(100);  \n   \n// get stable time source\n// Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x01);  \n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, 0x00); \n  delay(200);\n  \n// Configure device for bias calculation\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x00);   // Disable all interrupts\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x00);      // Disable FIFO\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x00);   // Turn on internal clock source\n  writeByte(MPU6050_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x00);    // Disable FIFO and I2C master modes\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x0C);    // Reset FIFO and DMP\n  delay(15);\n  \n// Configure MPU6050 gyro and accelerometer for bias calculation\n  writeByte(MPU6050_ADDRESS, CONFIG, 0x01);      // Set low-pass filter to 188 Hz\n  writeByte(MPU6050_ADDRESS, SMPLRT_DIV, 0x00);  // Set sample rate to 1 kHz\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, 0x00);  // Set gyro full-scale to 250 degrees per second, maximum sensitivity\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity\n \n  uint16_t  gyrosensitivity  = 131;   // = 131 LSB/degrees/sec\n  uint16_t  accelsensitivity = 16384;  // = 16384 LSB/g\n\n// Configure FIFO to capture accelerometer and gyro data for bias calculation\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x40);   // Enable FIFO  \n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x78);     // Enable gyro and accelerometer sensors for FIFO  (max size 1024 bytes in MPU-6050)\n  delay(80); // accumulate 80 samples in 80 milliseconds = 960 bytes\n\n// At end of sample accumulation, turn off FIFO sensor read\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x00);        // Disable gyro and accelerometer sensors for FIFO\n  readBytes(MPU6050_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count\n  fifo_count = ((uint16_t)data[0] << 8) | data[1];\n  packet_count = fifo_count/12;// How many sets of full gyro and accelerometer data for averaging\n\n  for (ii = 0; ii < packet_count; ii++) {\n    int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0};\n    readBytes(MPU6050_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging\n    accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1]  ) ;  // Form signed 16-bit integer for each sample in FIFO\n    accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3]  ) ;\n    accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5]  ) ;    \n    gyro_temp[0]  = (int16_t) (((int16_t)data[6] << 8) | data[7]  ) ;\n    gyro_temp[1]  = (int16_t) (((int16_t)data[8] << 8) | data[9]  ) ;\n    gyro_temp[2]  = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;\n    \n    accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases\n    accel_bias[1] += (int32_t) accel_temp[1];\n    accel_bias[2] += (int32_t) accel_temp[2];\n    gyro_bias[0]  += (int32_t) gyro_temp[0];\n    gyro_bias[1]  += (int32_t) gyro_temp[1];\n    gyro_bias[2]  += (int32_t) gyro_temp[2];\n            \n}\n    accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases\n    accel_bias[1] /= (int32_t) packet_count;\n    accel_bias[2] /= (int32_t) packet_count;\n    gyro_bias[0]  /= (int32_t) packet_count;\n    gyro_bias[1]  /= (int32_t) packet_count;\n    gyro_bias[2]  /= (int32_t) packet_count;\n    \n  if(accel_bias[2] > 0L) {accel_bias[2] -= (int32_t) accelsensitivity;}  // Remove gravity from the z-axis accelerometer bias calculation\n  else {accel_bias[2] += (int32_t) accelsensitivity;}\n \n// Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup\n  data[0] = (-gyro_bias[0]/4  >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format\n  data[1] = (-gyro_bias[0]/4)       & 0xFF; // Biases are additive, so change sign on calculated average gyro biases\n  data[2] = (-gyro_bias[1]/4  >> 8) & 0xFF;\n  data[3] = (-gyro_bias[1]/4)       & 0xFF;\n  data[4] = (-gyro_bias[2]/4  >> 8) & 0xFF;\n  data[5] = (-gyro_bias[2]/4)       & 0xFF;\n\n// Push gyro biases to hardware registers; works well for gyro but not for accelerometer\n//  writeByte(MPU6050_ADDRESS, XG_OFFS_USRH, data[0]); \n//  writeByte(MPU6050_ADDRESS, XG_OFFS_USRL, data[1]);\n//  writeByte(MPU6050_ADDRESS, YG_OFFS_USRH, data[2]);\n//  writeByte(MPU6050_ADDRESS, YG_OFFS_USRL, data[3]);\n//  writeByte(MPU6050_ADDRESS, ZG_OFFS_USRH, data[4]);\n//  writeByte(MPU6050_ADDRESS, ZG_OFFS_USRL, data[5]);\n\n  dest1[0] = (float) gyro_bias[0]/(float) gyrosensitivity; // construct gyro bias in deg/s for later manual subtraction\n  dest1[1] = (float) gyro_bias[1]/(float) gyrosensitivity;\n  dest1[2] = (float) gyro_bias[2]/(float) gyrosensitivity;\n\n// Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain\n// factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold\n// non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature\n// compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that\n// the accelerometer biases calculated above must be divided by 8.\n\n  int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases\n  readBytes(MPU6050_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values\n  accel_bias_reg[0] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  readBytes(MPU6050_ADDRESS, YA_OFFSET_H, 2, &data[0]);\n  accel_bias_reg[1] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  readBytes(MPU6050_ADDRESS, ZA_OFFSET_H, 2, &data[0]);\n  accel_bias_reg[2] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  \n  uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers\n  uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis\n  \n  for(ii = 0; ii < 3; ii++) {\n    if(accel_bias_reg[ii] & mask) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit\n  }\n\n  // Construct total accelerometer bias, including calculated average accelerometer bias from above\n  accel_bias_reg[0] -= (accel_bias[0]/8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale)\n  accel_bias_reg[1] -= (accel_bias[1]/8);\n  accel_bias_reg[2] -= (accel_bias[2]/8);\n \n  data[0] = (accel_bias_reg[0] >> 8) & 0xFF;\n  data[1] = (accel_bias_reg[0])      & 0xFF;\n  data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n  data[2] = (accel_bias_reg[1] >> 8) & 0xFF;\n  data[3] = (accel_bias_reg[1])      & 0xFF;\n  data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n  data[4] = (accel_bias_reg[2] >> 8) & 0xFF;\n  data[5] = (accel_bias_reg[2])      & 0xFF;\n  data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n\n  // Push accelerometer biases to hardware registers; doesn't work well for accelerometer\n  // Are we handling the temperature compensation bit correctly?\n//  writeByte(MPU6050_ADDRESS, XA_OFFSET_H, data[0]);  \n//  writeByte(MPU6050_ADDRESS, XA_OFFSET_L_TC, data[1]);\n//  writeByte(MPU6050_ADDRESS, YA_OFFSET_H, data[2]);\n//  writeByte(MPU6050_ADDRESS, YA_OFFSET_L_TC, data[3]);  \n//  writeByte(MPU6050_ADDRESS, ZA_OFFSET_H, data[4]);\n//  writeByte(MPU6050_ADDRESS, ZA_OFFSET_L_TC, data[5]);\n\n// Output scaled accelerometer biases for manual subtraction in the main program\n   dest2[0] = (float)accel_bias[0]/(float)accelsensitivity; \n   dest2[1] = (float)accel_bias[1]/(float)accelsensitivity;\n   dest2[2] = (float)accel_bias[2]/(float)accelsensitivity;\n}\n\n\n// Accelerometer and gyroscope self test; check calibration wrt factory settings\nvoid MPU6050SelfTest(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass\n{\n   uint8_t rawData[4];\n   uint8_t selfTest[6];\n   float factoryTrim[6];\n   \n   // Configure the accelerometer for self-test\n   writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, 0xF0); // Enable self test on all three axes and set accelerometer range to +/- 8 g\n   writeByte(MPU6050_ADDRESS, GYRO_CONFIG,  0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s\n   delay(250);  // Delay a while to let the device execute the self-test\n   rawData[0] = readByte(MPU6050_ADDRESS, SELF_TEST_X); // X-axis self-test results\n   rawData[1] = readByte(MPU6050_ADDRESS, SELF_TEST_Y); // Y-axis self-test results\n   rawData[2] = readByte(MPU6050_ADDRESS, SELF_TEST_Z); // Z-axis self-test results\n   rawData[3] = readByte(MPU6050_ADDRESS, SELF_TEST_A); // Mixed-axis self-test results\n   // Extract the acceleration test results first\n   selfTest[0] = (rawData[0] >> 3) | (rawData[3] & 0x30) >> 4 ; // XA_TEST result is a five-bit unsigned integer\n   selfTest[1] = (rawData[1] >> 3) | (rawData[3] & 0x0C) >> 2 ; // YA_TEST result is a five-bit unsigned integer\n   selfTest[2] = (rawData[2] >> 3) | (rawData[3] & 0x03) >> 0 ; // ZA_TEST result is a five-bit unsigned integer\n   // Extract the gyration test results first\n   selfTest[3] = rawData[0]  & 0x1F ; // XG_TEST result is a five-bit unsigned integer\n   selfTest[4] = rawData[1]  & 0x1F ; // YG_TEST result is a five-bit unsigned integer\n   selfTest[5] = rawData[2]  & 0x1F ; // ZG_TEST result is a five-bit unsigned integer   \n   // Process results to allow final comparison with factory set values\n   factoryTrim[0] = (4096.0*0.34)*(pow( (0.92/0.34) , (((float)selfTest[0] - 1.0)/30.0))); // FT[Xa] factory trim calculation\n   factoryTrim[1] = (4096.0*0.34)*(pow( (0.92/0.34) , (((float)selfTest[1] - 1.0)/30.0))); // FT[Ya] factory trim calculation\n   factoryTrim[2] = (4096.0*0.34)*(pow( (0.92/0.34) , (((float)selfTest[2] - 1.0)/30.0))); // FT[Za] factory trim calculation\n   factoryTrim[3] =  ( 25.0*131.0)*(pow( 1.046 , ((float)selfTest[3] - 1.0) ));             // FT[Xg] factory trim calculation\n   factoryTrim[4] =  (-25.0*131.0)*(pow( 1.046 , ((float)selfTest[4] - 1.0) ));             // FT[Yg] factory trim calculation\n   factoryTrim[5] =  ( 25.0*131.0)*(pow( 1.046 , ((float)selfTest[5] - 1.0) ));             // FT[Zg] factory trim calculation\n   \n //  Output self-test results and factory trim calculation if desired\n //  Serial.println(selfTest[0]); Serial.println(selfTest[1]); Serial.println(selfTest[2]);\n //  Serial.println(selfTest[3]); Serial.println(selfTest[4]); Serial.println(selfTest[5]);\n //  Serial.println(factoryTrim[0]); Serial.println(factoryTrim[1]); Serial.println(factoryTrim[2]);\n //  Serial.println(factoryTrim[3]); Serial.println(factoryTrim[4]); Serial.println(factoryTrim[5]);\n\n // Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response\n // To get to percent, must multiply by 100 and subtract result from 100\n   for (int i = 0; i < 6; i++) {\n     destination[i] = 100.0 + 100.0*((float)selfTest[i] - factoryTrim[i])/factoryTrim[i]; // Report percent differences\n   }\n   \n}\n\n  void writeByte(uint8_t address, uint8_t subAddress, uint8_t data)\n{\n\tWire.beginTransmission(address);  // Initialize the Tx buffer\n\tWire.write(subAddress);           // Put slave register address in Tx buffer\n\tWire.write(data);                 // Put data in Tx buffer\n\tWire.endTransmission();           // Send the Tx buffer\n}\n\n  uint8_t readByte(uint8_t address, uint8_t subAddress)\n{\n\tuint8_t data; // `data` will store the register data\t \n\tWire.beginTransmission(address);         // Initialize the Tx buffer\n\tWire.write(subAddress);\t                 // Put slave register address in Tx buffer\n\tWire.endTransmission(false);             // Send the Tx buffer, but send a restart to keep connection alive\n\tWire.requestFrom(address, (uint8_t) 1);  // Read one byte from slave register address \n\tdata = Wire.read();                      // Fill Rx buffer with result\n\treturn data;                             // Return data read from slave register\n}\n\n  void readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest)\n{  \n\tWire.beginTransmission(address);   // Initialize the Tx buffer\n\tWire.write(subAddress);            // Put slave register address in Tx buffer\n\tWire.endTransmission(false);       // Send the Tx buffer, but send a restart to keep connection alive\n\tuint8_t i = 0;\n        Wire.requestFrom(address, count);  // Read bytes from slave register address \n\twhile (Wire.available()) {\n        dest[i++] = Wire.read(); }         // Put read results in the Rx buffer\n}\n"
  },
  {
    "path": "MPU6050IMU.ino",
    "content": "/* MPU6050 Basic Example with IMU  \n by: Kris Winer\n date: May 10, 2014\n license: Beerware - Use this code however you'd like. If you \n find it useful you can buy me a beer some time.\n \n Demonstrate  MPU-6050 basic functionality including initialization, accelerometer trimming, sleep mode functionality as well as\n parameterizing the register addresses. Added display functions to allow display to on breadboard monitor. \n No DMP use. We just want to get out the accelerations, temperature, and gyro readings.\n \n SDA and SCL should have external pull-up resistors (to 3.3V).\n 10k resistors worked for me. They should be on the breakout\n board.\n \n Hardware setup:\n MPU6050 Breakout --------- Arduino\n 3.3V --------------------- 3.3V\n SDA ----------------------- A4\n SCL ----------------------- A5\n GND ---------------------- GND\n \n  Note: The MPU6050 is an I2C sensor and uses the Arduino Wire library. \n Because the sensor is not 5V tolerant, we are using a 3.3 V 8 MHz Pro Mini or a 3.3 V Teensy 3.1.\n We have disabled the internal pull-ups used by the Wire library in the Wire.h/twi.c utility file.\n We are also using the 400 kHz fast I2C mode by setting the TWI_FREQ  to 400000L /twi.h utility file.\n */\n \n#include <Wire.h>\n#include <Adafruit_GFX.h>\n#include <Adafruit_PCD8544.h>\n\n// Using NOKIA 5110 monochrome 84 x 48 pixel display\n// pin 9 - Serial clock out (SCLK)\n// pin 8 - Serial data out (DIN)\n// pin 7 - Data/Command select (D/C)\n// pin 5 - LCD chip select (CS)\n// pin 6 - LCD reset (RST)\nAdafruit_PCD8544 display = Adafruit_PCD8544(9, 8, 7, 5, 6);\n\n// Define registers per MPU6050, Register Map and Descriptions, Rev 4.2, 08/19/2013 6 DOF Motion sensor fusion device\n// Invensense Inc., www.invensense.com\n// See also MPU-6050 Register Map and Descriptions, Revision 4.0, RM-MPU-6050A-00, 9/12/2012 for registers not listed in \n// above document; the MPU6050 and MPU 9150 are virtually identical but the latter has an on-board magnetic sensor\n//\n#define XGOFFS_TC        0x00 // Bit 7 PWR_MODE, bits 6:1 XG_OFFS_TC, bit 0 OTP_BNK_VLD                 \n#define YGOFFS_TC        0x01                                                                          \n#define ZGOFFS_TC        0x02\n#define X_FINE_GAIN      0x03 // [7:0] fine gain\n#define Y_FINE_GAIN      0x04\n#define Z_FINE_GAIN      0x05\n#define XA_OFFSET_H      0x06 // User-defined trim values for accelerometer\n#define XA_OFFSET_L_TC   0x07\n#define YA_OFFSET_H      0x08\n#define YA_OFFSET_L_TC   0x09\n#define ZA_OFFSET_H      0x0A\n#define ZA_OFFSET_L_TC   0x0B\n#define SELF_TEST_X      0x0D\n#define SELF_TEST_Y      0x0E    \n#define SELF_TEST_Z      0x0F\n#define SELF_TEST_A      0x10\n#define XG_OFFS_USRH     0x13  // User-defined trim values for gyroscope; supported in MPU-6050?\n#define XG_OFFS_USRL     0x14\n#define YG_OFFS_USRH     0x15\n#define YG_OFFS_USRL     0x16\n#define ZG_OFFS_USRH     0x17\n#define ZG_OFFS_USRL     0x18\n#define SMPLRT_DIV       0x19\n#define CONFIG           0x1A\n#define GYRO_CONFIG      0x1B\n#define ACCEL_CONFIG     0x1C\n#define FF_THR           0x1D  // Free-fall\n#define FF_DUR           0x1E  // Free-fall\n#define MOT_THR          0x1F  // Motion detection threshold bits [7:0]\n#define MOT_DUR          0x20  // Duration counter threshold for motion interrupt generation, 1 kHz rate, LSB = 1 ms\n#define ZMOT_THR         0x21  // Zero-motion detection threshold bits [7:0]\n#define ZRMOT_DUR        0x22  // Duration counter threshold for zero motion interrupt generation, 16 Hz rate, LSB = 64 ms\n#define FIFO_EN          0x23\n#define I2C_MST_CTRL     0x24   \n#define I2C_SLV0_ADDR    0x25\n#define I2C_SLV0_REG     0x26\n#define I2C_SLV0_CTRL    0x27\n#define I2C_SLV1_ADDR    0x28\n#define I2C_SLV1_REG     0x29\n#define I2C_SLV1_CTRL    0x2A\n#define I2C_SLV2_ADDR    0x2B\n#define I2C_SLV2_REG     0x2C\n#define I2C_SLV2_CTRL    0x2D\n#define I2C_SLV3_ADDR    0x2E\n#define I2C_SLV3_REG     0x2F\n#define I2C_SLV3_CTRL    0x30\n#define I2C_SLV4_ADDR    0x31\n#define I2C_SLV4_REG     0x32\n#define I2C_SLV4_DO      0x33\n#define I2C_SLV4_CTRL    0x34\n#define I2C_SLV4_DI      0x35\n#define I2C_MST_STATUS   0x36\n#define INT_PIN_CFG      0x37\n#define INT_ENABLE       0x38\n#define DMP_INT_STATUS   0x39  // Check DMP interrupt\n#define INT_STATUS       0x3A\n#define ACCEL_XOUT_H     0x3B\n#define ACCEL_XOUT_L     0x3C\n#define ACCEL_YOUT_H     0x3D\n#define ACCEL_YOUT_L     0x3E\n#define ACCEL_ZOUT_H     0x3F\n#define ACCEL_ZOUT_L     0x40\n#define TEMP_OUT_H       0x41\n#define TEMP_OUT_L       0x42\n#define GYRO_XOUT_H      0x43\n#define GYRO_XOUT_L      0x44\n#define GYRO_YOUT_H      0x45\n#define GYRO_YOUT_L      0x46\n#define GYRO_ZOUT_H      0x47\n#define GYRO_ZOUT_L      0x48\n#define EXT_SENS_DATA_00 0x49\n#define EXT_SENS_DATA_01 0x4A\n#define EXT_SENS_DATA_02 0x4B\n#define EXT_SENS_DATA_03 0x4C\n#define EXT_SENS_DATA_04 0x4D\n#define EXT_SENS_DATA_05 0x4E\n#define EXT_SENS_DATA_06 0x4F\n#define EXT_SENS_DATA_07 0x50\n#define EXT_SENS_DATA_08 0x51\n#define EXT_SENS_DATA_09 0x52\n#define EXT_SENS_DATA_10 0x53\n#define EXT_SENS_DATA_11 0x54\n#define EXT_SENS_DATA_12 0x55\n#define EXT_SENS_DATA_13 0x56\n#define EXT_SENS_DATA_14 0x57\n#define EXT_SENS_DATA_15 0x58\n#define EXT_SENS_DATA_16 0x59\n#define EXT_SENS_DATA_17 0x5A\n#define EXT_SENS_DATA_18 0x5B\n#define EXT_SENS_DATA_19 0x5C\n#define EXT_SENS_DATA_20 0x5D\n#define EXT_SENS_DATA_21 0x5E\n#define EXT_SENS_DATA_22 0x5F\n#define EXT_SENS_DATA_23 0x60\n#define MOT_DETECT_STATUS 0x61\n#define I2C_SLV0_DO      0x63\n#define I2C_SLV1_DO      0x64\n#define I2C_SLV2_DO      0x65\n#define I2C_SLV3_DO      0x66\n#define I2C_MST_DELAY_CTRL 0x67\n#define SIGNAL_PATH_RESET  0x68\n#define MOT_DETECT_CTRL   0x69\n#define USER_CTRL        0x6A  // Bit 7 enable DMP, bit 3 reset DMP\n#define PWR_MGMT_1       0x6B // Device defaults to the SLEEP mode\n#define PWR_MGMT_2       0x6C\n#define DMP_BANK         0x6D  // Activates a specific bank in the DMP\n#define DMP_RW_PNT       0x6E  // Set read/write pointer to a specific start address in specified DMP bank\n#define DMP_REG          0x6F  // Register in DMP from which to read or to which to write\n#define DMP_REG_1        0x70\n#define DMP_REG_2        0x71\n#define FIFO_COUNTH      0x72\n#define FIFO_COUNTL      0x73\n#define FIFO_R_W         0x74\n#define WHO_AM_I_MPU6050 0x75 // Should return 0x68\n\n// Using the GY-521 breakout board, I set ADO to 0 by grounding through a 4k7 resistor\n// Seven-bit device address is 110100 for ADO = 0 and 110101 for ADO = 1\n#define ADO 0\n#if ADO\n#define MPU6050_ADDRESS 0x69  // Device address when ADO = 1\n#else\n#define MPU6050_ADDRESS 0x68  // Device address when ADO = 0\n#endif\n\n// Set initial input parameters\nenum Ascale {\n  AFS_2G = 0,\n  AFS_4G,\n  AFS_8G,\n  AFS_16G\n};\n\nenum Gscale {\n  GFS_250DPS = 0,\n  GFS_500DPS,\n  GFS_1000DPS,\n  GFS_2000DPS\n};\n\n// Specify sensor full scale\nint Gscale = GFS_250DPS;\nint Ascale = AFS_2G;\nfloat aRes, gRes; // scale resolutions per LSB for the sensors\n  \n// Pin definitions\nint intPin = 12;  // These can be changed, 2 and 3 are the Arduinos ext int pins\n#define blinkPin 13  // Blink LED on Teensy or Pro Mini when updating\nboolean blinkOn = false;\n\nint16_t accelCount[3];  // Stores the 16-bit signed accelerometer sensor output\nfloat ax, ay, az;       // Stores the real accel value in g's\nint16_t gyroCount[3];   // Stores the 16-bit signed gyro sensor output\nfloat gyrox, gyroy, gyroz;       // Stores the real gyro value in degrees per seconds\nfloat gyroBias[3] = {0, 0, 0}, accelBias[3] = {0, 0, 0}; // Bias corrections for gyro and accelerometer\nint16_t tempCount;   // Stores the real internal chip temperature in degrees Celsius\nfloat temperature;\nfloat SelfTest[6];\n\nuint32_t delt_t = 0; // used to control display output rate\nuint32_t count = 0;  // used to control display output rate\n\n// parameters for 6 DoF sensor fusion calculations\nfloat GyroMeasError = PI * (40.0f / 180.0f);     // gyroscope measurement error in rads/s (start at 60 deg/s), then reduce after ~10 s to 3\nfloat beta = sqrt(3.0f / 4.0f) * GyroMeasError;  // compute beta\nfloat GyroMeasDrift = PI * (2.0f / 180.0f);      // gyroscope measurement drift in rad/s/s (start at 0.0 deg/s/s)\nfloat zeta = sqrt(3.0f / 4.0f) * GyroMeasDrift;  // compute zeta, the other free parameter in the Madgwick scheme usually set to a small or zero value\nfloat pitch, yaw, roll;\nfloat deltat = 0.0f;                              // integration interval for both filter schemes\nuint32_t lastUpdate = 0, firstUpdate = 0;         // used to calculate integration interval\nuint32_t Now = 0;                                 // used to calculate integration interval\nfloat q[4] = {1.0f, 0.0f, 0.0f, 0.0f};            // vector to hold quaternion\n\nvoid setup()\n{\n  Wire.begin();\n  Serial.begin(38400);\n  \n  // Set up the interrupt pin, its set as active high, push-pull\n  pinMode(intPin, INPUT);\n  digitalWrite(intPin, LOW);\n  pinMode(blinkPin, OUTPUT);\n  digitalWrite(blinkPin, HIGH);\n  \n  display.begin(); // Initialize the display\n  display.setContrast(50); // Set the contrast\n  display.setRotation(2); //  0 or 2) width = width, 1 or 3) width = height, swapped etc.\n\n  \n// Start device display with ID of sensor\n  display.clearDisplay();\n  display.setTextSize(2);\n  display.setCursor(0,0); display.print(\"MPU6050\");\n  display.setTextSize(1);\n  display.setCursor(0, 20); display.print(\"6-DOF 16-bit\");\n  display.setCursor(0, 30); display.print(\"motion sensor\");\n  display.setCursor(20,40); display.print(\"60 ug LSB\");\n  display.display();\n  delay(1000);\n\n// Set up for data display\n  display.setTextSize(1); // Set text size to normal, 2 is twice normal etc.\n  display.setTextColor(BLACK); // Set pixel color; 1 on the monochrome screen\n  display.clearDisplay();   // clears the screen and buffer\n\n  // Read the WHO_AM_I register, this is a good test of communication\n  uint8_t c = readByte(MPU6050_ADDRESS, WHO_AM_I_MPU6050);  // Read WHO_AM_I register for MPU-6050\n  display.setCursor(20,0); display.print(\"MPU6050\");\n  display.setCursor(0,10); display.print(\"I AM\");\n  display.setCursor(0,20); display.print(c, HEX);  \n  display.setCursor(0,30); display.print(\"I Should Be\");\n  display.setCursor(0,40); display.print(0x68, HEX); \n  display.display();\n  delay(1000); \n\n  if (c == 0x68) // WHO_AM_I should always be 0x68\n  {  \n    Serial.println(\"MPU6050 is online...\");\n    \n    MPU6050SelfTest(SelfTest); // Start by performing self test and reporting values\n//    Serial.print(\"x-axis self test: acceleration trim within : \"); Serial.print(SelfTest[0],1); Serial.println(\"% of factory value\");\n//    Serial.print(\"y-axis self test: acceleration trim within : \"); Serial.print(SelfTest[1],1); Serial.println(\"% of factory value\");\n//    Serial.print(\"z-axis self test: acceleration trim within : \"); Serial.print(SelfTest[2],1); Serial.println(\"% of factory value\");\n//    Serial.print(\"x-axis self test: gyration trim within : \"); Serial.print(SelfTest[3],1); Serial.println(\"% of factory value\");\n//    Serial.print(\"y-axis self test: gyration trim within : \"); Serial.print(SelfTest[4],1); Serial.println(\"% of factory value\");\n//    Serial.print(\"z-axis self test: gyration trim within : \"); Serial.print(SelfTest[5],1); Serial.println(\"% of factory value\");\n\n    if(SelfTest[0] < 1.0f && SelfTest[1] < 1.0f && SelfTest[2] < 1.0f && SelfTest[3] < 1.0f && SelfTest[4] < 1.0f && SelfTest[5] < 1.0f) {\n    display.clearDisplay();\n    display.setCursor(0, 30); display.print(\"Pass Selftest!\");  \n    display.display();\n    delay(1000);\n  \n    calibrateMPU6050(gyroBias, accelBias); // Calibrate gyro and accelerometers, load biases in bias registers  \n  display.clearDisplay();\n     \n  display.setCursor(20, 0); display.print(\"MPU6050 bias\");\n  display.setCursor(0, 8); display.print(\" x   y   z  \");\n\n  display.setCursor(0,  16); display.print((int)(1000*accelBias[0])); \n  display.setCursor(24, 16); display.print((int)(1000*accelBias[1])); \n  display.setCursor(48, 16); display.print((int)(1000*accelBias[2])); \n  display.setCursor(72, 16); display.print(\"mg\");\n    \n  display.setCursor(0,  24); display.print(gyroBias[0], 1); \n  display.setCursor(24, 24); display.print(gyroBias[1], 1); \n  display.setCursor(48, 24); display.print(gyroBias[2], 1); \n  display.setCursor(66, 24); display.print(\"o/s\");   \n \n  display.display();\n  delay(1000); \n    \n   initMPU6050(); Serial.println(\"MPU6050 initialized for active data mode....\"); // Initialize device for active mode read of acclerometer, gyroscope, and temperature\n   }\n   else\n   {\n    Serial.print(\"Could not connect to MPU6050: 0x\");\n    Serial.println(c, HEX);\n    while(1) ; // Loop forever if communication doesn't happen\n   }\n  }\n}\n\nvoid loop()\n{  \n   // If data ready bit set, all data registers have new data\n  if(readByte(MPU6050_ADDRESS, INT_STATUS) & 0x01) {  // check if data ready interrupt\n    readAccelData(accelCount);  // Read the x/y/z adc values\n    getAres();\n    \n    // Now we'll calculate the accleration value into actual g's\n    ax = (float)accelCount[0]*aRes;  // get actual g value, this depends on scale being set\n    ay = (float)accelCount[1]*aRes;   \n    az = (float)accelCount[2]*aRes;  \n   \n    readGyroData(gyroCount);  // Read the x/y/z adc values\n    getGres();\n \n    // Calculate the gyro value into actual degrees per second\n    gyrox = (float)gyroCount[0]*gRes;  // get actual gyro value, this depends on scale being set\n    gyroy = (float)gyroCount[1]*gRes;  \n    gyroz = (float)gyroCount[2]*gRes;   \n\n    tempCount = readTempData();  // Read the x/y/z adc values\n    temperature = ((float) tempCount) / 340. + 36.53; // Temperature in degrees Centigrade\n   }  \n   \n    Now = micros();\n    deltat = ((Now - lastUpdate)/1000000.0f); // set integration time by time elapsed since last filter update\n    lastUpdate = Now;\n//    if(lastUpdate - firstUpdate > 10000000uL) {\n//      beta = 0.041; // decrease filter gain after stabilized\n//      zeta = 0.015; // increase gyro bias drift gain after stabilized\n//    }\n   // Pass gyro rate as rad/s\n    MadgwickQuaternionUpdate(ax, ay, az, gyrox*PI/180.0f, gyroy*PI/180.0f, gyroz*PI/180.0f);\n\n    // Serial print and/or display at 0.5 s rate independent of data rates\n    delt_t = millis() - count;\n    if (delt_t > 500) { // update LCD once per half-second independent of read rate\n    digitalWrite(blinkPin, blinkOn);\n/* \n    Serial.print(\"ax = \"); Serial.print((int)1000*ax);  \n    Serial.print(\" ay = \"); Serial.print((int)1000*ay); \n    Serial.print(\" az = \"); Serial.print((int)1000*az); Serial.println(\" mg\");\n\n    Serial.print(\"gyrox = \"); Serial.print( gyrox, 1); \n    Serial.print(\" gyroy = \"); Serial.print( gyroy, 1); \n    Serial.print(\" gyroz = \"); Serial.print( gyroz, 1); Serial.println(\" deg/s\");\n    \n    Serial.print(\"q0 = \"); Serial.print(q[0]);\n    Serial.print(\" qx = \"); Serial.print(q[1]); \n    Serial.print(\" qy = \"); Serial.print(q[2]); \n    Serial.print(\" qz = \"); Serial.println(q[3]);          \n*/    \n  // Define output variables from updated quaternion---these are Tait-Bryan angles, commonly used in aircraft orientation.\n  // In this coordinate system, the positive z-axis is down toward Earth. \n  // Yaw is the angle between Sensor x-axis and Earth magnetic North (or true North if corrected for local declination, looking down on the sensor positive yaw is counterclockwise.\n  // Pitch is angle between sensor x-axis and Earth ground plane, toward the Earth is positive, up toward the sky is negative.\n  // Roll is angle between sensor y-axis and Earth ground plane, y-axis up is positive roll.\n  // These arise from the definition of the homogeneous rotation matrix constructed from quaternions.\n  // Tait-Bryan angles as well as Euler angles are non-commutative; that is, the get the correct orientation the rotations must be\n  // applied in the correct order which for this configuration is yaw, pitch, and then roll.\n  // For more see http://en.wikipedia.org/wiki/Conversion_between_quaternions_and_Euler_angles which has additional links.\n    yaw   = atan2(2.0f * (q[1] * q[2] + q[0] * q[3]), q[0] * q[0] + q[1] * q[1] - q[2] * q[2] - q[3] * q[3]);   \n    pitch = -asin(2.0f * (q[1] * q[3] - q[0] * q[2]));\n    roll  = atan2(2.0f * (q[0] * q[1] + q[2] * q[3]), q[0] * q[0] - q[1] * q[1] - q[2] * q[2] + q[3] * q[3]);\n    pitch *= 180.0f / PI;\n    yaw   *= 180.0f / PI; \n    roll  *= 180.0f / PI;\n\n//    Serial.print(\"Yaw, Pitch, Roll: \");\n    Serial.print(yaw, 2);\n    Serial.print(\", \");\n    Serial.print(pitch, 2);\n    Serial.print(\", \");\n    Serial.println(roll, 2);\n\n//    Serial.print(\"average rate = \"); Serial.print(1.0f/deltat, 2); Serial.println(\" Hz\");\n    \n    display.clearDisplay();\n      \n    display.setCursor(0, 0); display.print(\" x   y   z  \");\n\n    display.setCursor(0,  8); display.print((int)(1000*ax)); \n    display.setCursor(24, 8); display.print((int)(1000*ay)); \n    display.setCursor(48, 8); display.print((int)(1000*az)); \n    display.setCursor(72, 8); display.print(\"mg\");\n    \n    display.setCursor(0,  16); display.print((int)(gyrox)); \n    display.setCursor(24, 16); display.print((int)(gyroy)); \n    display.setCursor(48, 16); display.print((int)(gyroz)); \n    display.setCursor(66, 16); display.print(\"o/s\");    \n \n    display.setCursor(0,  32); display.print((int)(yaw)); \n    display.setCursor(24, 32); display.print((int)(pitch)); \n    display.setCursor(48, 32); display.print((int)(roll)); \n    display.setCursor(66, 32); display.print(\"ypr\");  \n  \n    display.setCursor(0, 40); display.print(\"rt: \"); display.print(1.0f/deltat, 2); display.print(\" Hz\"); \n    display.display();\n    \n    blinkOn = ~blinkOn;\n    count = millis();  \n}\n  }\n\n//===================================================================================================================\n//====== Set of useful function to access acceleratio, gyroscope, and temperature data\n//===================================================================================================================\n\nvoid getGres() {\n  switch (Gscale)\n  {\n \t// Possible gyro scales (and their register bit settings) are:\n\t// 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS  (11). \n        // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:\n    case GFS_250DPS:\n          gRes = 250.0/32768.0;\n          break;\n    case GFS_500DPS:\n          gRes = 500.0/32768.0;\n          break;\n    case GFS_1000DPS:\n          gRes = 1000.0/32768.0;\n          break;\n    case GFS_2000DPS:\n          gRes = 2000.0/32768.0;\n          break;\n  }\n}\n\nvoid getAres() {\n  switch (Ascale)\n  {\n \t// Possible accelerometer scales (and their register bit settings) are:\n\t// 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs  (11). \n        // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:\n    case AFS_2G:\n          aRes = 2.0/32768.0;\n          break;\n    case AFS_4G:\n          aRes = 4.0/32768.0;\n          break;\n    case AFS_8G:\n          aRes = 8.0/32768.0;\n          break;\n    case AFS_16G:\n          aRes = 16.0/32768.0;\n          break;\n  }\n}\n\n\nvoid readAccelData(int16_t * destination)\n{\n  uint8_t rawData[6];  // x/y/z accel register data stored here\n  readBytes(MPU6050_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers into data array\n  destination[0] = (int16_t)((rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value\n  destination[1] = (int16_t)((rawData[2] << 8) | rawData[3]) ;  \n  destination[2] = (int16_t)((rawData[4] << 8) | rawData[5]) ; \n}\n\nvoid readGyroData(int16_t * destination)\n{\n  uint8_t rawData[6];  // x/y/z gyro register data stored here\n  readBytes(MPU6050_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers sequentially into data array\n  destination[0] = (int16_t)((rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value\n  destination[1] = (int16_t)((rawData[2] << 8) | rawData[3]) ;  \n  destination[2] = (int16_t)((rawData[4] << 8) | rawData[5]) ; \n}\n\nint16_t readTempData()\n{\n  uint8_t rawData[2];  // x/y/z gyro register data stored here\n  readBytes(MPU6050_ADDRESS, TEMP_OUT_H, 2, &rawData[0]);  // Read the two raw data registers sequentially into data array \n  return ((int16_t)rawData[0]) << 8 | rawData[1] ;  // Turn the MSB and LSB into a 16-bit value\n}\n\n\n\n// Configure the motion detection control for low power accelerometer mode\nvoid LowPowerAccelOnlyMPU6050()\n{\n\n// The sensor has a high-pass filter necessary to invoke to allow the sensor motion detection algorithms work properly\n// Motion detection occurs on free-fall (acceleration below a threshold for some time for all axes), motion (acceleration\n// above a threshold for some time on at least one axis), and zero-motion toggle (acceleration on each axis less than a \n// threshold for some time sets this flag, motion above the threshold turns it off). The high-pass filter takes gravity out\n// consideration for these threshold evaluations; otherwise, the flags would be set all the time!\n  \n  uint8_t c = readByte(MPU6050_ADDRESS, PWR_MGMT_1);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c & ~0x30); // Clear sleep and cycle bits [5:6]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c |  0x30); // Set sleep and cycle bits [5:6] to zero to make sure accelerometer is running\n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_2);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c & ~0x38); // Clear standby XA, YA, and ZA bits [3:5]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c |  0x00); // Set XA, YA, and ZA bits [3:5] to zero to make sure accelerometer is running\n    \n  c = readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x07); // Clear high-pass filter bits [2:0]\n// Set high-pass filter to 0) reset (disable), 1) 5 Hz, 2) 2.5 Hz, 3) 1.25 Hz, 4) 0.63 Hz, or 7) Hold\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG,  c | 0x00);  // Set ACCEL_HPF to 0; reset mode disbaling high-pass filter\n\n  c = readByte(MPU6050_ADDRESS, CONFIG);\n  writeByte(MPU6050_ADDRESS, CONFIG, c & ~0x07); // Clear low-pass filter bits [2:0]\n  writeByte(MPU6050_ADDRESS, CONFIG, c |  0x00);  // Set DLPD_CFG to 0; 260 Hz bandwidth, 1 kHz rate\n    \n  c = readByte(MPU6050_ADDRESS, INT_ENABLE);\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, c & ~0xFF);  // Clear all interrupts\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x40);  // Enable motion threshold (bits 5) interrupt only\n  \n// Motion detection interrupt requires the absolute value of any axis to lie above the detection threshold\n// for at least the counter duration\n  writeByte(MPU6050_ADDRESS, MOT_THR, 0x80); // Set motion detection to 0.256 g; LSB = 2 mg\n  writeByte(MPU6050_ADDRESS, MOT_DUR, 0x01); // Set motion detect duration to 1  ms; LSB is 1 ms @ 1 kHz rate\n  \n  delay (100);  // Add delay for accumulation of samples\n  \n  c = readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x07); // Clear high-pass filter bits [2:0]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c |  0x07);  // Set ACCEL_HPF to 7; hold the initial accleration value as a referance\n   \n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_2);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c & ~0xC7); // Clear standby XA, YA, and ZA bits [3:5] and LP_WAKE_CTRL bits [6:7]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c |  0x47); // Set wakeup frequency to 5 Hz, and disable XG, YG, and ZG gyros (bits [0:2])  \n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_1);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c & ~0x20); // Clear sleep and cycle bit 5\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c |  0x20); // Set cycle bit 5 to begin low power accelerometer motion interrupts\n\n}\n\n\nvoid initMPU6050()\n{  \n// wake up device-don't need this here if using calibration function below\n//  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors \n//  delay(100); // Delay 100 ms for PLL to get established on x-axis gyro; should check for PLL ready interrupt  \n\n // get stable time source\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x01);  // Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001\n\n // Configure Gyro and Accelerometer\n // Disable FSYNC and set accelerometer and gyro bandwidth to 44 and 42 Hz, respectively; \n // DLPF_CFG = bits 2:0 = 010; this sets the sample rate at 1 kHz for both\n // Maximum delay time is 4.9 ms corresponding to just over 200 Hz sample rate\n  writeByte(MPU6050_ADDRESS, CONFIG, 0x03);  \n \n // Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV)\n  writeByte(MPU6050_ADDRESS, SMPLRT_DIV, 0x04);  // Use a 200 Hz rate; the same rate set in CONFIG above\n \n // Set gyroscope full scale range\n // Range selects FS_SEL and AFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3\n  uint8_t c =  readByte(MPU6050_ADDRESS, GYRO_CONFIG);\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c & ~0xE0); // Clear self-test bits [7:5] \n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c & ~0x18); // Clear AFS bits [4:3]\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c | Gscale << 3); // Set full scale range for the gyro\n   \n // Set accelerometer configuration\n  c =  readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0xE0); // Clear self-test bits [7:5] \n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x18); // Clear AFS bits [4:3]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c | Ascale << 3); // Set full scale range for the accelerometer \n\n  // Configure Interrupts and Bypass Enable\n  // Set interrupt pin active high, push-pull, and clear on read of INT_STATUS, enable I2C_BYPASS_EN so additional chips \n  // can join the I2C bus and all can be controlled by the Arduino as master\n   writeByte(MPU6050_ADDRESS, INT_PIN_CFG, 0x22);    \n   writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x01);  // Enable data ready (bit 0) interrupt\n}\n\n// Function which accumulates gyro and accelerometer data after device initialization. It calculates the average\n// of the at-rest readings and then loads the resulting offsets into accelerometer and gyro bias registers.\nvoid calibrateMPU6050(float * dest1, float * dest2)\n{  \n  uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data\n  uint16_t ii, packet_count, fifo_count;\n  int32_t gyro_bias[3] = {0, 0, 0}, accel_bias[3] = {0, 0, 0};\n  \n// reset device, reset all registers, clear gyro and accelerometer bias registers\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device\n  delay(100);  \n   \n// get stable time source\n// Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x01);  \n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, 0x00); \n  delay(200);\n  \n// Configure device for bias calculation\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x00);   // Disable all interrupts\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x00);      // Disable FIFO\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x00);   // Turn on internal clock source\n  writeByte(MPU6050_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x00);    // Disable FIFO and I2C master modes\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x0C);    // Reset FIFO and DMP\n  delay(15);\n  \n// Configure MPU6050 gyro and accelerometer for bias calculation\n  writeByte(MPU6050_ADDRESS, CONFIG, 0x01);      // Set low-pass filter to 188 Hz\n  writeByte(MPU6050_ADDRESS, SMPLRT_DIV, 0x00);  // Set sample rate to 1 kHz\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, 0x00);  // Set gyro full-scale to 250 degrees per second, maximum sensitivity\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity\n \n  uint16_t  gyrosensitivity  = 131;   // = 131 LSB/degrees/sec\n  uint16_t  accelsensitivity = 16384;  // = 16384 LSB/g\n\n// Configure FIFO to capture accelerometer and gyro data for bias calculation\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x40);   // Enable FIFO  \n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x78);     // Enable gyro and accelerometer sensors for FIFO  (max size 1024 bytes in MPU-6050)\n  delay(80); // accumulate 80 samples in 80 milliseconds = 960 bytes\n\n// At end of sample accumulation, turn off FIFO sensor read\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x00);        // Disable gyro and accelerometer sensors for FIFO\n  readBytes(MPU6050_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count\n  fifo_count = ((uint16_t)data[0] << 8) | data[1];\n  packet_count = fifo_count/12;// How many sets of full gyro and accelerometer data for averaging\n\n  for (ii = 0; ii < packet_count; ii++) {\n    int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0};\n    readBytes(MPU6050_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging\n    accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1]  ) ;  // Form signed 16-bit integer for each sample in FIFO\n    accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3]  ) ;\n    accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5]  ) ;    \n    gyro_temp[0]  = (int16_t) (((int16_t)data[6] << 8) | data[7]  ) ;\n    gyro_temp[1]  = (int16_t) (((int16_t)data[8] << 8) | data[9]  ) ;\n    gyro_temp[2]  = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;\n    \n    accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases\n    accel_bias[1] += (int32_t) accel_temp[1];\n    accel_bias[2] += (int32_t) accel_temp[2];\n    gyro_bias[0]  += (int32_t) gyro_temp[0];\n    gyro_bias[1]  += (int32_t) gyro_temp[1];\n    gyro_bias[2]  += (int32_t) gyro_temp[2];\n            \n}\n    accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases\n    accel_bias[1] /= (int32_t) packet_count;\n    accel_bias[2] /= (int32_t) packet_count;\n    gyro_bias[0]  /= (int32_t) packet_count;\n    gyro_bias[1]  /= (int32_t) packet_count;\n    gyro_bias[2]  /= (int32_t) packet_count;\n    \n  if(accel_bias[2] > 0L) {accel_bias[2] -= (int32_t) accelsensitivity;}  // Remove gravity from the z-axis accelerometer bias calculation\n  else {accel_bias[2] += (int32_t) accelsensitivity;}\n \n// Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup\n  data[0] = (-gyro_bias[0]/4  >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format\n  data[1] = (-gyro_bias[0]/4)       & 0xFF; // Biases are additive, so change sign on calculated average gyro biases\n  data[2] = (-gyro_bias[1]/4  >> 8) & 0xFF;\n  data[3] = (-gyro_bias[1]/4)       & 0xFF;\n  data[4] = (-gyro_bias[2]/4  >> 8) & 0xFF;\n  data[5] = (-gyro_bias[2]/4)       & 0xFF;\n\n// Push gyro biases to hardware registers\n  writeByte(MPU6050_ADDRESS, XG_OFFS_USRH, data[0]);// might not be supported in MPU6050\n  writeByte(MPU6050_ADDRESS, XG_OFFS_USRL, data[1]);\n  writeByte(MPU6050_ADDRESS, YG_OFFS_USRH, data[2]);\n  writeByte(MPU6050_ADDRESS, YG_OFFS_USRL, data[3]);\n  writeByte(MPU6050_ADDRESS, ZG_OFFS_USRH, data[4]);\n  writeByte(MPU6050_ADDRESS, ZG_OFFS_USRL, data[5]);\n\n  dest1[0] = (float) gyro_bias[0]/(float) gyrosensitivity; // construct gyro bias in deg/s for later manual subtraction\n  dest1[1] = (float) gyro_bias[1]/(float) gyrosensitivity;\n  dest1[2] = (float) gyro_bias[2]/(float) gyrosensitivity;\n\n// Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain\n// factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold\n// non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature\n// compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that\n// the accelerometer biases calculated above must be divided by 8.\n\n  int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases\n  readBytes(MPU6050_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values\n  accel_bias_reg[0] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  readBytes(MPU6050_ADDRESS, YA_OFFSET_H, 2, &data[0]);\n  accel_bias_reg[1] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  readBytes(MPU6050_ADDRESS, ZA_OFFSET_H, 2, &data[0]);\n  accel_bias_reg[2] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  \n  uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers\n  uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis\n  \n  for(ii = 0; ii < 3; ii++) {\n    if(accel_bias_reg[ii] & mask) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit\n  }\n\n  // Construct total accelerometer bias, including calculated average accelerometer bias from above\n  accel_bias_reg[0] -= (accel_bias[0]/8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale)\n  accel_bias_reg[1] -= (accel_bias[1]/8);\n  accel_bias_reg[2] -= (accel_bias[2]/8);\n \n  data[0] = (accel_bias_reg[0] >> 8) & 0xFF;\n  data[1] = (accel_bias_reg[0])      & 0xFF;\n  data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n  data[2] = (accel_bias_reg[1] >> 8) & 0xFF;\n  data[3] = (accel_bias_reg[1])      & 0xFF;\n  data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n  data[4] = (accel_bias_reg[2] >> 8) & 0xFF;\n  data[5] = (accel_bias_reg[2])      & 0xFF;\n  data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n\n  // Push accelerometer biases to hardware registers\n  writeByte(MPU6050_ADDRESS, XA_OFFSET_H, data[0]); // might not be supported in MPU6050\n  writeByte(MPU6050_ADDRESS, XA_OFFSET_L_TC, data[1]);\n  writeByte(MPU6050_ADDRESS, YA_OFFSET_H, data[2]);\n  writeByte(MPU6050_ADDRESS, YA_OFFSET_L_TC, data[3]);  \n  writeByte(MPU6050_ADDRESS, ZA_OFFSET_H, data[4]);\n  writeByte(MPU6050_ADDRESS, ZA_OFFSET_L_TC, data[5]);\n\n// Output scaled accelerometer biases for manual subtraction in the main program\n   dest2[0] = (float)accel_bias[0]/(float)accelsensitivity; \n   dest2[1] = (float)accel_bias[1]/(float)accelsensitivity;\n   dest2[2] = (float)accel_bias[2]/(float)accelsensitivity;\n}\n\n\n// Accelerometer and gyroscope self test; check calibration wrt factory settings\nvoid MPU6050SelfTest(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass\n{\n   uint8_t rawData[4];\n   uint8_t selfTest[6];\n   float factoryTrim[6];\n   \n   // Configure the accelerometer for self-test\n   writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, 0xF0); // Enable self test on all three axes and set accelerometer range to +/- 8 g\n   writeByte(MPU6050_ADDRESS, GYRO_CONFIG,  0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s\n   delay(250);  // Delay a while to let the device execute the self-test\n   rawData[0] = readByte(MPU6050_ADDRESS, SELF_TEST_X); // X-axis self-test results\n   rawData[1] = readByte(MPU6050_ADDRESS, SELF_TEST_Y); // Y-axis self-test results\n   rawData[2] = readByte(MPU6050_ADDRESS, SELF_TEST_Z); // Z-axis self-test results\n   rawData[3] = readByte(MPU6050_ADDRESS, SELF_TEST_A); // Mixed-axis self-test results\n   // Extract the acceleration test results first\n   selfTest[0] = (rawData[0] >> 3) | (rawData[3] & 0x30) >> 4 ; // XA_TEST result is a five-bit unsigned integer\n   selfTest[1] = (rawData[1] >> 3) | (rawData[3] & 0x0C) >> 2 ; // YA_TEST result is a five-bit unsigned integer\n   selfTest[2] = (rawData[2] >> 3) | (rawData[3] & 0x03) ; // ZA_TEST result is a five-bit unsigned integer\n   // Extract the gyration test results first\n   selfTest[3] = rawData[0]  & 0x1F ; // XG_TEST result is a five-bit unsigned integer\n   selfTest[4] = rawData[1]  & 0x1F ; // YG_TEST result is a five-bit unsigned integer\n   selfTest[5] = rawData[2]  & 0x1F ; // ZG_TEST result is a five-bit unsigned integer   \n   // Process results to allow final comparison with factory set values\n   factoryTrim[0] = (4096.0*0.34)*(pow( (0.92/0.34) , (((float)selfTest[0] - 1.0)/30.0))); // FT[Xa] factory trim calculation\n   factoryTrim[1] = (4096.0*0.34)*(pow( (0.92/0.34) , (((float)selfTest[1] - 1.0)/30.0))); // FT[Ya] factory trim calculation\n   factoryTrim[2] = (4096.0*0.34)*(pow( (0.92/0.34) , (((float)selfTest[2] - 1.0)/30.0))); // FT[Za] factory trim calculation\n   factoryTrim[3] =  ( 25.0*131.0)*(pow( 1.046 , ((float)selfTest[3] - 1.0) ));             // FT[Xg] factory trim calculation\n   factoryTrim[4] =  (-25.0*131.0)*(pow( 1.046 , ((float)selfTest[4] - 1.0) ));             // FT[Yg] factory trim calculation\n   factoryTrim[5] =  ( 25.0*131.0)*(pow( 1.046 , ((float)selfTest[5] - 1.0) ));             // FT[Zg] factory trim calculation\n   \n //  Output self-test results and factory trim calculation if desired\n //  Serial.println(selfTest[0]); Serial.println(selfTest[1]); Serial.println(selfTest[2]);\n //  Serial.println(selfTest[3]); Serial.println(selfTest[4]); Serial.println(selfTest[5]);\n //  Serial.println(factoryTrim[0]); Serial.println(factoryTrim[1]); Serial.println(factoryTrim[2]);\n //  Serial.println(factoryTrim[3]); Serial.println(factoryTrim[4]); Serial.println(factoryTrim[5]);\n\n // Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response\n // To get to percent, must multiply by 100 and subtract result from 100\n   for (int i = 0; i < 6; i++) {\n     destination[i] = 100.0 + 100.0*((float)selfTest[i] - factoryTrim[i])/factoryTrim[i]; // Report percent differences\n   }\n   \n}\n\n        void writeByte(uint8_t address, uint8_t subAddress, uint8_t data)\n{\n\tWire.beginTransmission(address);  // Initialize the Tx buffer\n\tWire.write(subAddress);           // Put slave register address in Tx buffer\n\tWire.write(data);                 // Put data in Tx buffer\n\tWire.endTransmission();           // Send the Tx buffer\n}\n\n        uint8_t readByte(uint8_t address, uint8_t subAddress)\n{\n\tuint8_t data; // `data` will store the register data\t \n\tWire.beginTransmission(address);         // Initialize the Tx buffer\n\tWire.write(subAddress);\t                 // Put slave register address in Tx buffer\n\tWire.endTransmission(false);             // Send the Tx buffer, but send a restart to keep connection alive\n\tWire.requestFrom(address, (uint8_t) 1);  // Read one byte from slave register address \n\tdata = Wire.read();                      // Fill Rx buffer with result\n\treturn data;                             // Return data read from slave register\n}\n\n        void readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest)\n{  \n\tWire.beginTransmission(address);   // Initialize the Tx buffer\n\tWire.write(subAddress);            // Put slave register address in Tx buffer\n\tWire.endTransmission(false);       // Send the Tx buffer, but send a restart to keep connection alive\n\tuint8_t i = 0;\n        Wire.requestFrom(address, count);  // Read bytes from slave register address \n\twhile (Wire.available()) {\n        dest[i++] = Wire.read(); }         // Put read results in the Rx buffer\n}\n"
  },
  {
    "path": "MPU6050Library/MPU6050.cpp",
    "content": "#include \"MPU6050.h\"\nint Gscale = GFS_250DPS;\nint Ascale = AFS_2G;\n\nfloat MPU6050lib::getGres() {\n  switch (Gscale)\n  {\n    // Possible gyro scales (and their register bit settings) are:\n    // 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS  (11).\n    // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:\n    case GFS_250DPS:\n      return 250.0 / 32768.0;\n      break;\n    case GFS_500DPS:\n      return 500.0 / 32768.0;\n      break;\n    case GFS_1000DPS:\n      return 1000.0 / 32768.0;\n      break;\n    case GFS_2000DPS:\n      return 2000.0 / 32768.0;\n      break;\n  }\n}\n\nfloat MPU6050lib::getAres() {\n  switch (Ascale)\n  {\n    // Possible accelerometer scales (and their register bit settings) are:\n    // 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs  (11).\n    // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:\n    case AFS_2G:\n      return 2.0 / 32768.0;\n      break;\n    case AFS_4G:\n      return 4.0 / 32768.0;\n      break;\n    case AFS_8G:\n      return 8.0 / 32768.0;\n      break;\n    case AFS_16G:\n      return 16.0 / 32768.0;\n      break;\n  }\n}\n\n\nvoid MPU6050lib::readAccelData(int16_t * destination)\n{\n  uint8_t rawData[6];  // x/y/z accel register data stored here\n  readBytes(MPU6050_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers into data array\n  destination[0] = (int16_t)((rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value\n  destination[1] = (int16_t)((rawData[2] << 8) | rawData[3]) ;\n  destination[2] = (int16_t)((rawData[4] << 8) | rawData[5]) ;\n}\n\nvoid MPU6050lib::readGyroData(int16_t * destination)\n{\n  uint8_t rawData[6];  // x/y/z gyro register data stored here\n  readBytes(MPU6050_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers sequentially into data array\n  destination[0] = (int16_t)((rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value\n  destination[1] = (int16_t)((rawData[2] << 8) | rawData[3]) ;\n  destination[2] = (int16_t)((rawData[4] << 8) | rawData[5]) ;\n}\n\nint16_t MPU6050lib::readTempData()\n{\n  uint8_t rawData[2];  // x/y/z gyro register data stored here\n  readBytes(MPU6050_ADDRESS, TEMP_OUT_H, 2, &rawData[0]);  // Read the two raw data registers sequentially into data array\n  return ((int16_t)rawData[0]) << 8 | rawData[1] ;  // Turn the MSB and LSB into a 16-bit value\n}\n\n\n\n// Configure the motion detection control for low power accelerometer mode\nvoid MPU6050lib::LowPowerAccelOnlyMPU6050()\n{\n\n  // The sensor has a high-pass filter necessary to invoke to allow the sensor motion detection algorithms work properly\n  // Motion detection occurs on free-fall (acceleration below a threshold for some time for all axes), motion (acceleration\n  // above a threshold for some time on at least one axis), and zero-motion toggle (acceleration on each axis less than a\n  // threshold for some time sets this flag, motion above the threshold turns it off). The high-pass filter takes gravity out\n  // consideration for these threshold evaluations; otherwise, the flags would be set all the time!\n\n  uint8_t c = readByte(MPU6050_ADDRESS, PWR_MGMT_1);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c & ~0x30); // Clear sleep and cycle bits [5:6]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c |  0x30); // Set sleep and cycle bits [5:6] to zero to make sure accelerometer is running\n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_2);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c & ~0x38); // Clear standby XA, YA, and ZA bits [3:5]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c |  0x00); // Set XA, YA, and ZA bits [3:5] to zero to make sure accelerometer is running\n\n  c = readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x07); // Clear high-pass filter bits [2:0]\n  // Set high-pass filter to 0) reset (disable), 1) 5 Hz, 2) 2.5 Hz, 3) 1.25 Hz, 4) 0.63 Hz, or 7) Hold\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG,  c | 0x00);  // Set ACCEL_HPF to 0; reset mode disbaling high-pass filter\n\n  c = readByte(MPU6050_ADDRESS, CONFIG);\n  writeByte(MPU6050_ADDRESS, CONFIG, c & ~0x07); // Clear low-pass filter bits [2:0]\n  writeByte(MPU6050_ADDRESS, CONFIG, c |  0x00);  // Set DLPD_CFG to 0; 260 Hz bandwidth, 1 kHz rate\n\n  c = readByte(MPU6050_ADDRESS, INT_ENABLE);\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, c & ~0xFF);  // Clear all interrupts\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x40);  // Enable motion threshold (bits 5) interrupt only\n\n  // Motion detection interrupt requires the absolute value of any axis to lie above the detection threshold\n  // for at least the counter duration\n  writeByte(MPU6050_ADDRESS, MOT_THR, 0x80); // Set motion detection to 0.256 g; LSB = 2 mg\n  writeByte(MPU6050_ADDRESS, MOT_DUR, 0x01); // Set motion detect duration to 1  ms; LSB is 1 ms @ 1 kHz rate\n\n  delay (100);  // Add delay for accumulation of samples\n\n  c = readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x07); // Clear high-pass filter bits [2:0]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c |  0x07);  // Set ACCEL_HPF to 7; hold the initial accleration value as a referance\n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_2);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c & ~0xC7); // Clear standby XA, YA, and ZA bits [3:5] and LP_WAKE_CTRL bits [6:7]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c |  0x47); // Set wakeup frequency to 5 Hz, and disable XG, YG, and ZG gyros (bits [0:2])\n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_1);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c & ~0x20); // Clear sleep and cycle bit 5\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c |  0x20); // Set cycle bit 5 to begin low power accelerometer motion interrupts\n\n}\n\n\nvoid MPU6050lib::initMPU6050()\n{\n  // wake up device-don't need this here if using calibration function below\n  //  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors\n  //  delay(100); // Delay 100 ms for PLL to get established on x-axis gyro; should check for PLL ready interrupt\n\n  // get stable time source\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x01);  // Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001\n\n  // Configure Gyro and Accelerometer\n  // Disable FSYNC and set accelerometer and gyro bandwidth to 44 and 42 Hz, respectively;\n  // DLPF_CFG = bits 2:0 = 010; this sets the sample rate at 1 kHz for both\n  // Maximum delay time is 4.9 ms corresponding to just over 200 Hz sample rate\n  writeByte(MPU6050_ADDRESS, CONFIG, 0x03);\n\n  // Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV)\n  writeByte(MPU6050_ADDRESS, SMPLRT_DIV, 0x04);  // Use a 200 Hz rate; the same rate set in CONFIG above\n\n  // Set gyroscope full scale range\n  // Range selects FS_SEL and AFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3\n  uint8_t c =  readByte(MPU6050_ADDRESS, GYRO_CONFIG);\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c & ~0xE0); // Clear self-test bits [7:5]\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c & ~0x18); // Clear AFS bits [4:3]\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c | Gscale << 3); // Set full scale range for the gyro\n\n  // Set accelerometer configuration\n  c =  readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0xE0); // Clear self-test bits [7:5]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x18); // Clear AFS bits [4:3]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c | Ascale << 3); // Set full scale range for the accelerometer\n\n  // Configure Interrupts and Bypass Enable\n  // Set interrupt pin active high, push-pull, and clear on read of INT_STATUS, enable I2C_BYPASS_EN so additional chips\n  // can join the I2C bus and all can be controlled by the Arduino as master\n  writeByte(MPU6050_ADDRESS, INT_PIN_CFG, 0x22);\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x01);  // Enable data ready (bit 0) interrupt\n}\n\n// Function which accumulates gyro and accelerometer data after device initialization. It calculates the average\n// of the at-rest readings and then loads the resulting offsets into accelerometer and gyro bias registers.\nvoid MPU6050lib::calibrateMPU6050(float * dest1, float * dest2)\n{\n  uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data\n  uint16_t ii, packet_count, fifo_count;\n  int32_t gyro_bias[3] = {0, 0, 0}, accel_bias[3] = {0, 0, 0};\n\n  // reset device, reset all registers, clear gyro and accelerometer bias registers\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device\n  delay(100);\n\n  // get stable time source\n  // Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x01);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, 0x00);\n  delay(200);\n\n  // Configure device for bias calculation\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x00);   // Disable all interrupts\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x00);      // Disable FIFO\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x00);   // Turn on internal clock source\n  writeByte(MPU6050_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x00);    // Disable FIFO and I2C master modes\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x0C);    // Reset FIFO and DMP\n  delay(15);\n\n  // Configure MPU6050 gyro and accelerometer for bias calculation\n  writeByte(MPU6050_ADDRESS, CONFIG, 0x01);      // Set low-pass filter to 188 Hz\n  writeByte(MPU6050_ADDRESS, SMPLRT_DIV, 0x00);  // Set sample rate to 1 kHz\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, 0x00);  // Set gyro full-scale to 250 degrees per second, maximum sensitivity\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity\n\n  uint16_t  gyrosensitivity  = 131;   // = 131 LSB/degrees/sec\n  uint16_t  accelsensitivity = 16384;  // = 16384 LSB/g\n\n  // Configure FIFO to capture accelerometer and gyro data for bias calculation\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x40);   // Enable FIFO\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x78);     // Enable gyro and accelerometer sensors for FIFO  (max size 1024 bytes in MPU-6050)\n  delay(80); // accumulate 80 samples in 80 milliseconds = 960 bytes\n\n  // At end of sample accumulation, turn off FIFO sensor read\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x00);        // Disable gyro and accelerometer sensors for FIFO\n  readBytes(MPU6050_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count\n  fifo_count = ((uint16_t)data[0] << 8) | data[1];\n  packet_count = fifo_count / 12; // How many sets of full gyro and accelerometer data for averaging\n\n  for (ii = 0; ii < packet_count; ii++) {\n    int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0};\n    readBytes(MPU6050_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging\n    accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1]  ) ;  // Form signed 16-bit integer for each sample in FIFO\n    accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3]  ) ;\n    accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5]  ) ;\n    gyro_temp[0]  = (int16_t) (((int16_t)data[6] << 8) | data[7]  ) ;\n    gyro_temp[1]  = (int16_t) (((int16_t)data[8] << 8) | data[9]  ) ;\n    gyro_temp[2]  = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;\n\n    accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases\n    accel_bias[1] += (int32_t) accel_temp[1];\n    accel_bias[2] += (int32_t) accel_temp[2];\n    gyro_bias[0]  += (int32_t) gyro_temp[0];\n    gyro_bias[1]  += (int32_t) gyro_temp[1];\n    gyro_bias[2]  += (int32_t) gyro_temp[2];\n\n  }\n  accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases\n  accel_bias[1] /= (int32_t) packet_count;\n  accel_bias[2] /= (int32_t) packet_count;\n  gyro_bias[0]  /= (int32_t) packet_count;\n  gyro_bias[1]  /= (int32_t) packet_count;\n  gyro_bias[2]  /= (int32_t) packet_count;\n\n  if (accel_bias[2] > 0L) {\n    accel_bias[2] -= (int32_t) accelsensitivity; // Remove gravity from the z-axis accelerometer bias calculation\n  }\n  else {\n    accel_bias[2] += (int32_t) accelsensitivity;\n  }\n\n  // Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup\n  data[0] = (-gyro_bias[0] / 4  >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format\n  data[1] = (-gyro_bias[0] / 4)       & 0xFF; // Biases are additive, so change sign on calculated average gyro biases\n  data[2] = (-gyro_bias[1] / 4  >> 8) & 0xFF;\n  data[3] = (-gyro_bias[1] / 4)       & 0xFF;\n  data[4] = (-gyro_bias[2] / 4  >> 8) & 0xFF;\n  data[5] = (-gyro_bias[2] / 4)       & 0xFF;\n\n  // Push gyro biases to hardware registers\n  writeByte(MPU6050_ADDRESS, XG_OFFS_USRH, data[0]);// might not be supported in MPU6050\n  writeByte(MPU6050_ADDRESS, XG_OFFS_USRL, data[1]);\n  writeByte(MPU6050_ADDRESS, YG_OFFS_USRH, data[2]);\n  writeByte(MPU6050_ADDRESS, YG_OFFS_USRL, data[3]);\n  writeByte(MPU6050_ADDRESS, ZG_OFFS_USRH, data[4]);\n  writeByte(MPU6050_ADDRESS, ZG_OFFS_USRL, data[5]);\n\n  dest1[0] = (float) gyro_bias[0] / (float) gyrosensitivity; // construct gyro bias in deg/s for later manual subtraction\n  dest1[1] = (float) gyro_bias[1] / (float) gyrosensitivity;\n  dest1[2] = (float) gyro_bias[2] / (float) gyrosensitivity;\n\n  // Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain\n  // factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold\n  // non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature\n  // compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that\n  // the accelerometer biases calculated above must be divided by 8.\n\n  int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases\n  readBytes(MPU6050_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values\n  accel_bias_reg[0] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  readBytes(MPU6050_ADDRESS, YA_OFFSET_H, 2, &data[0]);\n  accel_bias_reg[1] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  readBytes(MPU6050_ADDRESS, ZA_OFFSET_H, 2, &data[0]);\n  accel_bias_reg[2] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n\n  uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers\n  uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis\n\n  for (ii = 0; ii < 3; ii++) {\n    if (accel_bias_reg[ii] & mask) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit\n  }\n\n  // Construct total accelerometer bias, including calculated average accelerometer bias from above\n  accel_bias_reg[0] -= (accel_bias[0] / 8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale)\n  accel_bias_reg[1] -= (accel_bias[1] / 8);\n  accel_bias_reg[2] -= (accel_bias[2] / 8);\n\n  data[0] = (accel_bias_reg[0] >> 8) & 0xFF;\n  data[1] = (accel_bias_reg[0])      & 0xFF;\n  data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n  data[2] = (accel_bias_reg[1] >> 8) & 0xFF;\n  data[3] = (accel_bias_reg[1])      & 0xFF;\n  data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n  data[4] = (accel_bias_reg[2] >> 8) & 0xFF;\n  data[5] = (accel_bias_reg[2])      & 0xFF;\n  data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n\n  // Push accelerometer biases to hardware registers\n  writeByte(MPU6050_ADDRESS, XA_OFFSET_H, data[0]); // might not be supported in MPU6050\n  writeByte(MPU6050_ADDRESS, XA_OFFSET_L_TC, data[1]);\n  writeByte(MPU6050_ADDRESS, YA_OFFSET_H, data[2]);\n  writeByte(MPU6050_ADDRESS, YA_OFFSET_L_TC, data[3]);\n  writeByte(MPU6050_ADDRESS, ZA_OFFSET_H, data[4]);\n  writeByte(MPU6050_ADDRESS, ZA_OFFSET_L_TC, data[5]);\n\n  // Output scaled accelerometer biases for manual subtraction in the main program\n  dest2[0] = (float)accel_bias[0] / (float)accelsensitivity;\n  dest2[1] = (float)accel_bias[1] / (float)accelsensitivity;\n  dest2[2] = (float)accel_bias[2] / (float)accelsensitivity;\n}\n\n\n// Accelerometer and gyroscope self test; check calibration wrt factory settings\nvoid MPU6050lib::MPU6050SelfTest(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass\n{\n  uint8_t rawData[4];\n  uint8_t selfTest[6];\n  float factoryTrim[6];\n\n  // Configure the accelerometer for self-test\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, 0xF0); // Enable self test on all three axes and set accelerometer range to +/- 8 g\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG,  0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s\n  delay(250);  // Delay a while to let the device execute the self-test\n  rawData[0] = readByte(MPU6050_ADDRESS, SELF_TEST_X); // X-axis self-test results\n  rawData[1] = readByte(MPU6050_ADDRESS, SELF_TEST_Y); // Y-axis self-test results\n  rawData[2] = readByte(MPU6050_ADDRESS, SELF_TEST_Z); // Z-axis self-test results\n  rawData[3] = readByte(MPU6050_ADDRESS, SELF_TEST_A); // Mixed-axis self-test results\n  // Extract the acceleration test results first\n  selfTest[0] = (rawData[0] >> 3) | (rawData[3] & 0x30) >> 4 ; // XA_TEST result is a five-bit unsigned integer\n  selfTest[1] = (rawData[1] >> 3) | (rawData[3] & 0x0C) >> 2 ; // YA_TEST result is a five-bit unsigned integer\n  selfTest[2] = (rawData[2] >> 3) | (rawData[3] & 0x03) ; // ZA_TEST result is a five-bit unsigned integer\n  // Extract the gyration test results first\n  selfTest[3] = rawData[0]  & 0x1F ; // XG_TEST result is a five-bit unsigned integer\n  selfTest[4] = rawData[1]  & 0x1F ; // YG_TEST result is a five-bit unsigned integer\n  selfTest[5] = rawData[2]  & 0x1F ; // ZG_TEST result is a five-bit unsigned integer\n  // Process results to allow final comparison with factory set values\n  factoryTrim[0] = (4096.0 * 0.34) * (pow( (0.92 / 0.34) , (((float)selfTest[0] - 1.0) / 30.0))); // FT[Xa] factory trim calculation\n  factoryTrim[1] = (4096.0 * 0.34) * (pow( (0.92 / 0.34) , (((float)selfTest[1] - 1.0) / 30.0))); // FT[Ya] factory trim calculation\n  factoryTrim[2] = (4096.0 * 0.34) * (pow( (0.92 / 0.34) , (((float)selfTest[2] - 1.0) / 30.0))); // FT[Za] factory trim calculation\n  factoryTrim[3] =  ( 25.0 * 131.0) * (pow( 1.046 , ((float)selfTest[3] - 1.0) ));         // FT[Xg] factory trim calculation\n  factoryTrim[4] =  (-25.0 * 131.0) * (pow( 1.046 , ((float)selfTest[4] - 1.0) ));         // FT[Yg] factory trim calculation\n  factoryTrim[5] =  ( 25.0 * 131.0) * (pow( 1.046 , ((float)selfTest[5] - 1.0) ));         // FT[Zg] factory trim calculation\n\n  //  Output self-test results and factory trim calculation if desired\n  //  Serial.println(selfTest[0]); Serial.println(selfTest[1]); Serial.println(selfTest[2]);\n  //  Serial.println(selfTest[3]); Serial.println(selfTest[4]); Serial.println(selfTest[5]);\n  //  Serial.println(factoryTrim[0]); Serial.println(factoryTrim[1]); Serial.println(factoryTrim[2]);\n  //  Serial.println(factoryTrim[3]); Serial.println(factoryTrim[4]); Serial.println(factoryTrim[5]);\n\n  // Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response\n  // To get to percent, must multiply by 100 and subtract result from 100\n  for (int i = 0; i < 6; i++) {\n    destination[i] = 100.0 + 100.0 * ((float)selfTest[i] - factoryTrim[i]) / factoryTrim[i]; // Report percent differences\n  }\n\n}\n\nvoid MPU6050lib::writeByte(uint8_t address, uint8_t subAddress, uint8_t data)\n{\n  Wire.beginTransmission(address);  // Initialize the Tx buffer\n  Wire.write(subAddress);           // Put slave register address in Tx buffer\n  Wire.write(data);                 // Put data in Tx buffer\n  Wire.endTransmission();           // Send the Tx buffer\n}\n\nuint8_t MPU6050lib::readByte(uint8_t address, uint8_t subAddress)\n{\n  uint8_t data; // `data` will store the register data\n  Wire.beginTransmission(address);         // Initialize the Tx buffer\n  Wire.write(subAddress);\t                 // Put slave register address in Tx buffer\n  Wire.endTransmission(false);             // Send the Tx buffer, but send a restart to keep connection alive\n  Wire.requestFrom(address, (uint8_t) 1);  // Read one byte from slave register address\n  data = Wire.read();                      // Fill Rx buffer with result\n  return data;                             // Return data read from slave register\n}\n\nvoid MPU6050lib::readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest)\n{\n  Wire.beginTransmission(address);   // Initialize the Tx buffer\n  Wire.write(subAddress);            // Put slave register address in Tx buffer\n  Wire.endTransmission(false);       // Send the Tx buffer, but send a restart to keep connection alive\n  uint8_t i = 0;\n  Wire.requestFrom(address, count);  // Read bytes from slave register address\n  while (Wire.available()) {\n    dest[i++] = Wire.read();\n  }         // Put read results in the Rx buffer\n}\n"
  },
  {
    "path": "MPU6050Library/MPU6050.h",
    "content": "#include \"Arduino.h\"\n#include \"Wire.h\"\n// Using the GY-521 breakout board, I set ADO to 0 by grounding through a 4k7 resistor\n// Seven-bit device address is 110100 for ADO = 0 and 110101 for ADO = 1\n#define ADO 0\n#if ADO\n#define MPU6050_ADDRESS 0x69  // Device address when ADO = 1\n#else\n#define MPU6050_ADDRESS 0x68  // Device address when ADO = 0\n#endif\n// Set initial input parameters\nenum Ascale {\n  AFS_2G = 0,\n  AFS_4G,\n  AFS_8G,\n  AFS_16G\n};\n\nenum Gscale {\n  GFS_250DPS = 0,\n  GFS_500DPS,\n  GFS_1000DPS,\n  GFS_2000DPS\n};\n\n#define XGOFFS_TC        0x00 // Bit 7 PWR_MODE, bits 6:1 XG_OFFS_TC, bit 0 OTP_BNK_VLD\n#define YGOFFS_TC        0x01\n#define ZGOFFS_TC        0x02\n#define X_FINE_GAIN      0x03 // [7:0] fine gain\n#define Y_FINE_GAIN      0x04\n#define Z_FINE_GAIN      0x05\n#define XA_OFFSET_H      0x06 // User-defined trim values for accelerometer\n#define XA_OFFSET_L_TC   0x07\n#define YA_OFFSET_H      0x08\n#define YA_OFFSET_L_TC   0x09\n#define ZA_OFFSET_H      0x0A\n#define ZA_OFFSET_L_TC   0x0B\n#define SELF_TEST_X      0x0D\n#define SELF_TEST_Y      0x0E\n#define SELF_TEST_Z      0x0F\n#define SELF_TEST_A      0x10\n#define XG_OFFS_USRH     0x13  // User-defined trim values for gyroscope; supported in MPU-6050?\n#define XG_OFFS_USRL     0x14\n#define YG_OFFS_USRH     0x15\n#define YG_OFFS_USRL     0x16\n#define ZG_OFFS_USRH     0x17\n#define ZG_OFFS_USRL     0x18\n#define SMPLRT_DIV       0x19\n#define CONFIG           0x1A\n#define GYRO_CONFIG      0x1B\n#define ACCEL_CONFIG     0x1C\n#define FF_THR           0x1D  // Free-fall\n#define FF_DUR           0x1E  // Free-fall\n#define MOT_THR          0x1F  // Motion detection threshold bits [7:0]\n#define MOT_DUR          0x20  // Duration counter threshold for motion interrupt generation, 1 kHz rate, LSB = 1 ms\n#define ZMOT_THR         0x21  // Zero-motion detection threshold bits [7:0]\n#define ZRMOT_DUR        0x22  // Duration counter threshold for zero motion interrupt generation, 16 Hz rate, LSB = 64 ms\n#define FIFO_EN          0x23\n#define I2C_MST_CTRL     0x24\n#define I2C_SLV0_ADDR    0x25\n#define I2C_SLV0_REG     0x26\n#define I2C_SLV0_CTRL    0x27\n#define I2C_SLV1_ADDR    0x28\n#define I2C_SLV1_REG     0x29\n#define I2C_SLV1_CTRL    0x2A\n#define I2C_SLV2_ADDR    0x2B\n#define I2C_SLV2_REG     0x2C\n#define I2C_SLV2_CTRL    0x2D\n#define I2C_SLV3_ADDR    0x2E\n#define I2C_SLV3_REG     0x2F\n#define I2C_SLV3_CTRL    0x30\n#define I2C_SLV4_ADDR    0x31\n#define I2C_SLV4_REG     0x32\n#define I2C_SLV4_DO      0x33\n#define I2C_SLV4_CTRL    0x34\n#define I2C_SLV4_DI      0x35\n#define I2C_MST_STATUS   0x36\n#define INT_PIN_CFG      0x37\n#define INT_ENABLE       0x38\n#define DMP_INT_STATUS   0x39  // Check DMP interrupt\n#define INT_STATUS       0x3A\n#define ACCEL_XOUT_H     0x3B\n#define ACCEL_XOUT_L     0x3C\n#define ACCEL_YOUT_H     0x3D\n#define ACCEL_YOUT_L     0x3E\n#define ACCEL_ZOUT_H     0x3F\n#define ACCEL_ZOUT_L     0x40\n#define TEMP_OUT_H       0x41\n#define TEMP_OUT_L       0x42\n#define GYRO_XOUT_H      0x43\n#define GYRO_XOUT_L      0x44\n#define GYRO_YOUT_H      0x45\n#define GYRO_YOUT_L      0x46\n#define GYRO_ZOUT_H      0x47\n#define GYRO_ZOUT_L      0x48\n#define EXT_SENS_DATA_00 0x49\n#define EXT_SENS_DATA_01 0x4A\n#define EXT_SENS_DATA_02 0x4B\n#define EXT_SENS_DATA_03 0x4C\n#define EXT_SENS_DATA_04 0x4D\n#define EXT_SENS_DATA_05 0x4E\n#define EXT_SENS_DATA_06 0x4F\n#define EXT_SENS_DATA_07 0x50\n#define EXT_SENS_DATA_08 0x51\n#define EXT_SENS_DATA_09 0x52\n#define EXT_SENS_DATA_10 0x53\n#define EXT_SENS_DATA_11 0x54\n#define EXT_SENS_DATA_12 0x55\n#define EXT_SENS_DATA_13 0x56\n#define EXT_SENS_DATA_14 0x57\n#define EXT_SENS_DATA_15 0x58\n#define EXT_SENS_DATA_16 0x59\n#define EXT_SENS_DATA_17 0x5A\n#define EXT_SENS_DATA_18 0x5B\n#define EXT_SENS_DATA_19 0x5C\n#define EXT_SENS_DATA_20 0x5D\n#define EXT_SENS_DATA_21 0x5E\n#define EXT_SENS_DATA_22 0x5F\n#define EXT_SENS_DATA_23 0x60\n#define MOT_DETECT_STATUS 0x61\n#define I2C_SLV0_DO      0x63\n#define I2C_SLV1_DO      0x64\n#define I2C_SLV2_DO      0x65\n#define I2C_SLV3_DO      0x66\n#define I2C_MST_DELAY_CTRL 0x67\n#define SIGNAL_PATH_RESET  0x68\n#define MOT_DETECT_CTRL   0x69\n#define USER_CTRL        0x6A  // Bit 7 enable DMP, bit 3 reset DMP\n#define PWR_MGMT_1       0x6B // Device defaults to the SLEEP mode\n#define PWR_MGMT_2       0x6C\n#define DMP_BANK         0x6D  // Activates a specific bank in the DMP\n#define DMP_RW_PNT       0x6E  // Set read/write pointer to a specific start address in specified DMP bank\n#define DMP_REG          0x6F  // Register in DMP from which to read or to which to write\n#define DMP_REG_1        0x70\n#define DMP_REG_2        0x71\n#define FIFO_COUNTH      0x72\n#define FIFO_COUNTL      0x73\n#define FIFO_R_W         0x74\n#define WHO_AM_I_MPU6050 0x75 // Should return 0x68\n\nclass MPU6050lib\n{\npublic:\nfloat getGres();\nfloat getAres();\nvoid readAccelData(int16_t * destination);\nvoid readGyroData(int16_t * destination);\nint16_t readTempData();\nvoid LowPowerAccelOnlyMPU6050();\nvoid initMPU6050();\nvoid calibrateMPU6050(float * dest1, float * dest2);\nvoid MPU6050SelfTest(float * destination);\nvoid writeByte(uint8_t address, uint8_t subAddress, uint8_t data);\nuint8_t readByte(uint8_t address, uint8_t subAddress);\nvoid readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest);\n};\n"
  },
  {
    "path": "MPU6050Library/MPU6050BasicExample.ino",
    "content": "/* MPU6050 Basic Example Code\n by: Kris Winer\n date: May 1, 2014\n license: Beerware - Use this code however you'd like. If you \n find it useful you can buy me a beer some time.\n \n Demonstrate  MPU-6050 basic functionality including initialization, accelerometer trimming, sleep mode functionality as well as\n parameterizing the register addresses. Added display functions to allow display to on breadboard monitor. \n No DMP use. We just want to get out the accelerations, temperature, and gyro readings.\n \n SDA and SCL should have external pull-up resistors (to 3.3V).\n 10k resistors worked for me. They should be on the breakout\n board.\n \n Hardware setup:\n MPU6050 Breakout --------- Arduino\n 3.3V --------------------- 3.3V\n SDA ----------------------- A4\n SCL ----------------------- A5\n GND ---------------------- GND\n \n  Note: The MPU6050 is an I2C sensor and uses the Arduino Wire library. \n Because the sensor is not 5V tolerant, we are using a 3.3 V 8 MHz Pro Mini or a 3.3 V Teensy 3.1.\n We have disabled the internal pull-ups used by the Wire library in the Wire.h/twi.c utility file.\n We are also using the 400 kHz fast I2C mode by setting the TWI_FREQ  to 400000L /twi.h utility file.\n */\n \n#include <Wire.h>\n#include \"MPU6050.h\"\n// Using the GY-521 breakout board, I set ADO to 0 by grounding through a 4k7 resistor\n// Seven-bit device address is 110100 for ADO = 0 and 110101 for ADO = 1\n\n// Pin definitions\nint intPin = 12;  // This can be changed, 2 and 3 are the Arduinos ext int pins\nint16_t accelCount[3];           // Stores the 16-bit signed accelerometer sensor output\nfloat ax, ay, az;                // Stores the real accel value in g's\nint16_t gyroCount[3];            // Stores the 16-bit signed gyro sensor output\nfloat gyrox, gyroy, gyroz;                // Stores the real gyro value in degrees per seconds\nfloat gyroBias[3], accelBias[3]; // Bias corrections for gyro and accelerometer\nint16_t tempCount;               // Stores the internal chip temperature sensor output \nfloat temperature;               // Scaled temperature in degrees Celsius\nfloat SelfTest[6];               // Gyro and accelerometer self-test sensor output\nuint32_t count = 0;\nfloat aRes, gRes; // scale resolutions per LSB for the sensors\nMPU6050lib mpu;\nvoid setup()\n{\n  Wire.begin();\n  Serial.begin(9600);\n  \n  // Set up the interrupt pin, its set as active high, push-pull\n  pinMode(intPin, INPUT);\n  digitalWrite(intPin, LOW);\n  \n  Serial.println(\"MPU6050\");\n  Serial.println(\"6-DOF 16-bit\");\n  Serial.println(\"motion sensor\");\n  Serial.println(\"60 ug LSB\");\n \n   // Read the WHO_AM_I register, this is a good test of communication\n  uint8_t c = mpu.readByte(MPU6050_ADDRESS, WHO_AM_I_MPU6050);  // Read WHO_AM_I register for MPU-6050\n  Serial.print(\"I AM \");\n  Serial.print(c, HEX);  \n  Serial.print(\" I Should Be \");\n  Serial.println(0x68, HEX); \n\n  if (c == 0x68) // WHO_AM_I should always be 0x68\n  {  \n    Serial.println(\"MPU6050 is online...\");\n    \n    mpu.MPU6050SelfTest(SelfTest); // Start by performing self test and reporting values\n    Serial.print(\"x-axis self test: acceleration trim within : \"); Serial.print(SelfTest[0],1); Serial.println(\"% of factory value\");\n    Serial.print(\"y-axis self test: acceleration trim within : \"); Serial.print(SelfTest[1],1); Serial.println(\"% of factory value\");\n    Serial.print(\"z-axis self test: acceleration trim within : \"); Serial.print(SelfTest[2],1); Serial.println(\"% of factory value\");\n    Serial.print(\"x-axis self test: gyration trim within : \"); Serial.print(SelfTest[3],1); Serial.println(\"% of factory value\");\n    Serial.print(\"y-axis self test: gyration trim within : \"); Serial.print(SelfTest[4],1); Serial.println(\"% of factory value\");\n    Serial.print(\"z-axis self test: gyration trim within : \"); Serial.print(SelfTest[5],1); Serial.println(\"% of factory value\");\n\n    if(SelfTest[0] < 1.0f && SelfTest[1] < 1.0f && SelfTest[2] < 1.0f && SelfTest[3] < 1.0f && SelfTest[4] < 1.0f && SelfTest[5] < 1.0f) {\n    Serial.println(\"Pass Selftest!\");  \n      \n    mpu.calibrateMPU6050(gyroBias, accelBias); // Calibrate gyro and accelerometers, load biases in bias registers  \n    mpu.initMPU6050(); Serial.println(\"MPU6050 initialized for active data mode....\"); // Initialize device for active mode read of acclerometer, gyroscope, and temperature\n\n   }\n   else\n   {\n    Serial.print(\"Could not connect to MPU6050: 0x\");\n    Serial.println(c, HEX);\n    while(1) ; // Loop forever if communication doesn't happen\n   }\n\n  }\n}\n\nvoid loop()\n{  \n  // If data ready bit set, all data registers have new data\n  if(mpu.readByte(MPU6050_ADDRESS, INT_STATUS) & 0x01) {  // check if data ready interrupt\n\n    mpu.readAccelData(accelCount);  // Read the x/y/z adc values\n    aRes=mpu.getAres();\n    \n    // Now we'll calculate the accleration value into actual g's\n    ax = (float)accelCount[0]*aRes - accelBias[0];  // get actual g value, this depends on scale being set\n    ay = (float)accelCount[1]*aRes - accelBias[1];   \n    az = (float)accelCount[2]*aRes - accelBias[2];  \n   \n    mpu.readGyroData(gyroCount);  // Read the x/y/z adc values\n    gRes=mpu.getGres();\n \n    // Calculate the gyro value into actual degrees per second\n    gyrox = (float)gyroCount[0]*gRes - gyroBias[0];  // get actual gyro value, this depends on scale being set\n    gyroy = (float)gyroCount[1]*gRes - gyroBias[1];  \n    gyroz = (float)gyroCount[2]*gRes - gyroBias[2];   \n\n    tempCount = mpu.readTempData();  // Read the x/y/z adc values\n    temperature = ((float) tempCount) / 340. + 36.53; // Temperature in degrees Centigrade\n   }  \n   \n    uint32_t deltat = millis() - count;\n    if(deltat > 500) {\n \n    // Print acceleration values in milligs!\n    Serial.print(\"X-acceleration: \"); Serial.print(1000*ax); Serial.print(\" mg \"); \n    Serial.print(\"Y-acceleration: \"); Serial.print(1000*ay); Serial.print(\" mg \"); \n    Serial.print(\"Z-acceleration: \"); Serial.print(1000*az); Serial.println(\" mg\"); \n \n    // Print gyro values in degree/sec\n    Serial.print(\"X-gyro rate: \"); Serial.print(gyrox, 1); Serial.print(\" degrees/sec \"); \n    Serial.print(\"Y-gyro rate: \"); Serial.print(gyroy, 1); Serial.print(\" degrees/sec \"); \n    Serial.print(\"Z-gyro rate: \"); Serial.print(gyroz, 1); Serial.println(\" degrees/sec\"); \n    \n   // Print temperature in degrees Centigrade      \n    Serial.print(\"Temperature is \");  Serial.print(temperature, 2);  Serial.println(\" degrees C\"); // Print T values to tenths of s degree C\n    Serial.println(\"\");\n        \n    count = millis();\n    }\n\n}\n"
  },
  {
    "path": "MPU6050Library/MPU6050IMU.ino",
    "content": "/* MPU6050 Basic Example with IMU\n  by: Kris Winer\n  date: May 10, 2014\n  license: Beerware - Use this code however you'd like. If you\n  find it useful you can buy me a beer some time.\n\n  Demonstrate  MPU-6050 basic functionality including initialization, accelerometer trimming, sleep mode functionality as well as\n  parameterizing the register addresses. Added display functions to allow display to on breadboard monitor.\n  No DMP use. We just want to get out the accelerations, temperature, and gyro readings.\n\n  SDA and SCL should have external pull-up resistors (to 3.3V).\n  10k resistors worked for me. They should be on the breakout\n  board.\n\n  Hardware setup:\n  MPU6050 Breakout --------- Arduino\n  3.3V --------------------- 3.3V\n  SDA ----------------------- A4\n  SCL ----------------------- A5\n  GND ---------------------- GND\n\n  Note: The MPU6050 is an I2C sensor and uses the Arduino Wire library.\n  Because the sensor is not 5V tolerant, we are using a 3.3 V 8 MHz Pro Mini or a 3.3 V Teensy 3.1.\n  We have disabled the internal pull-ups used by the Wire library in the Wire.h/twi.c utility file.\n  We are also using the 400 kHz fast I2C mode by setting the TWI_FREQ  to 400000L /twi.h utility file.\n*/\n\n#include <Wire.h>\n#include \"MPU6050lib.h\"\nMPU6050lib mpu;\n\nfloat aRes, gRes; // scale resolutions per LSB for the sensors\n// Pin definitions\nint intPin = 12;  // These can be changed, 2 and 3 are the Arduinos ext int pins\n#define blinkPin 13  // Blink LED on Teensy or Pro Mini when updating\nboolean blinkOn = false;\nint16_t accelCount[3];  // Stores the 16-bit signed accelerometer sensor output\nfloat ax, ay, az;       // Stores the real accel value in g's\nint16_t gyroCount[3];   // Stores the 16-bit signed gyro sensor output\nfloat gyrox, gyroy, gyroz;       // Stores the real gyro value in degrees per seconds\nfloat gyroBias[3] = {0, 0, 0}, accelBias[3] = {0, 0, 0}; // Bias corrections for gyro and accelerometer\nint16_t tempCount;   // Stores the real internal chip temperature in degrees Celsius\nfloat temperature;\nfloat SelfTest[6];\nfloat q[4] = {1.0f, 0.0f, 0.0f, 0.0f};            // vector to hold quaternion\nuint32_t delt_t = 0; // used to control display output rate\nuint32_t count = 0;  // used to control display output rate\nfloat pitch, yaw, roll;\n// parameters for 6 DoF sensor fusion calculations\nfloat GyroMeasError = PI * (40.0f / 180.0f);     // gyroscope measurement error in rads/s (start at 60 deg/s), then reduce after ~10 s to 3\nfloat beta = sqrt(3.0f / 4.0f) * GyroMeasError;  // compute beta\nfloat GyroMeasDrift = PI * (2.0f / 180.0f);      // gyroscope measurement drift in rad/s/s (start at 0.0 deg/s/s)\nfloat zeta = sqrt(3.0f / 4.0f) * GyroMeasDrift;  // compute zeta, the other free parameter in the Madgwick scheme usually set to a small or zero value\nfloat deltat = 0.0f;                              // integration interval for both filter schemes\nuint32_t lastUpdate = 0, firstUpdate = 0;         // used to calculate integration interval\nuint32_t Now = 0;                                 // used to calculate integration interval\n\nvoid setup()\n{\n  Wire.begin();\n  Serial.begin(9600);\n\n  // Set up the interrupt pin, its set as active high, push-pull\n  pinMode(intPin, INPUT);\n  digitalWrite(intPin, LOW);\n  pinMode(blinkPin, OUTPUT);\n  digitalWrite(blinkPin, HIGH);\n\n  // Read the WHO_AM_I register, this is a good test of communication\n  uint8_t c = mpu.readByte(MPU6050_ADDRESS, WHO_AM_I_MPU6050);  // Read WHO_AM_I register for MPU-6050\n  Serial.print(\"I AM \");\n  Serial.print(c, HEX);\n  Serial.print(\" I Should Be \");\n  Serial.println(0x68, HEX);\n\n  if (c == 0x68) // WHO_AM_I should always be 0x68\n  {\n    Serial.println(\"MPU6050 is online...\");\n\n    mpu.MPU6050SelfTest(SelfTest); // Start by performing self test and reporting values\n    //    Serial.print(\"x-axis self test: acceleration trim within : \"); Serial.print(SelfTest[0],1); Serial.println(\"% of factory value\");\n    //    Serial.print(\"y-axis self test: acceleration trim within : \"); Serial.print(SelfTest[1],1); Serial.println(\"% of factory value\");\n    //    Serial.print(\"z-axis self test: acceleration trim within : \"); Serial.print(SelfTest[2],1); Serial.println(\"% of factory value\");\n    //    Serial.print(\"x-axis self test: gyration trim within : \"); Serial.print(SelfTest[3],1); Serial.println(\"% of factory value\");\n    //    Serial.print(\"y-axis self test: gyration trim within : \"); Serial.print(SelfTest[4],1); Serial.println(\"% of factory value\");\n    //    Serial.print(\"z-axis self test: gyration trim within : \"); Serial.print(SelfTest[5],1); Serial.println(\"% of factory value\");\n\n    if (SelfTest[0] < 1.0f && SelfTest[1] < 1.0f && SelfTest[2] < 1.0f && SelfTest[3] < 1.0f && SelfTest[4] < 1.0f && SelfTest[5] < 1.0f) {\n      Serial.println(\"Pass Selftest!\");\n\n      mpu.calibrateMPU6050(gyroBias, accelBias); // Calibrate gyro and accelerometers, load biases in bias registers\n      Serial.println(\"MPU6050 bias\");\n      Serial.println(\" x\\t  y\\t  z  \");\n      Serial.print((int)(1000 * accelBias[0])); Serial.print('\\t');\n      Serial.print((int)(1000 * accelBias[1])); Serial.print('\\t');\n      Serial.print((int)(1000 * accelBias[2]));\n      Serial.println(\" mg\");\n\n      Serial.print(gyroBias[0], 1); Serial.print('\\t');\n      Serial.print(gyroBias[1], 1); Serial.print('\\t');\n      Serial.print(gyroBias[2], 1);\n      Serial.println(\" o/s\");\n\n\n      mpu.initMPU6050(); Serial.println(\"MPU6050 initialized for active data mode....\"); // Initialize device for active mode read of acclerometer, gyroscope, and temperature\n    }\n    else\n    {\n      Serial.print(\"Could not connect to MPU6050: 0x\");\n      Serial.println(c, HEX);\n      while (1) ; // Loop forever if communication doesn't happen\n    }\n  }\n}\n\nvoid loop()\n{\n  // If data ready bit set, all data registers have new data\n  if (mpu.readByte(MPU6050_ADDRESS, INT_STATUS) & 0x01) { // check if data ready interrupt\n    mpu.readAccelData(accelCount);  // Read the x/y/z adc values\n    aRes = mpu.getAres();\n\n    // Now we'll calculate the accleration value into actual g's\n    ax = (float)accelCount[0] * aRes; // get actual g value, this depends on scale being set\n    ay = (float)accelCount[1] * aRes;\n    az = (float)accelCount[2] * aRes;\n\n    mpu.readGyroData(gyroCount);  // Read the x/y/z adc values\n    gRes = mpu.getGres();\n\n    // Calculate the gyro value into actual degrees per second\n    gyrox = (float)gyroCount[0] * gRes; // get actual gyro value, this depends on scale being set\n    gyroy = (float)gyroCount[1] * gRes;\n    gyroz = (float)gyroCount[2] * gRes;\n\n    tempCount = mpu.readTempData();  // Read the x/y/z adc values\n    temperature = ((float) tempCount) / 340. + 36.53; // Temperature in degrees Centigrade\n  }\n\n  Now = micros();\n  deltat = ((Now - lastUpdate) / 1000000.0f); // set integration time by time elapsed since last filter update\n  lastUpdate = Now;\n  //    if(lastUpdate - firstUpdate > 10000000uL) {\n  //      beta = 0.041; // decrease filter gain after stabilized\n  //      zeta = 0.015; // increase gyro bias drift gain after stabilized\n  //    }\n  // Pass gyro rate as rad/s\n  MadgwickQuaternionUpdate(ax, ay, az, gyrox * PI / 180.0f, gyroy * PI / 180.0f, gyroz * PI / 180.0f);\n\n  // Serial print and/or display at 0.5 s rate independent of data rates\n  delt_t = millis() - count;\n  if (delt_t > 500) { // update LCD once per half-second independent of read rate\n    digitalWrite(blinkPin, blinkOn);\n    /*\n        Serial.print(\"ax = \"); Serial.print((int)1000*ax);\n        Serial.print(\" ay = \"); Serial.print((int)1000*ay);\n        Serial.print(\" az = \"); Serial.print((int)1000*az); Serial.println(\" mg\");\n\n        Serial.print(\"gyrox = \"); Serial.print( gyrox, 1);\n        Serial.print(\" gyroy = \"); Serial.print( gyroy, 1);\n        Serial.print(\" gyroz = \"); Serial.print( gyroz, 1); Serial.println(\" deg/s\");\n\n        Serial.print(\"q0 = \"); Serial.print(q[0]);\n        Serial.print(\" qx = \"); Serial.print(q[1]);\n        Serial.print(\" qy = \"); Serial.print(q[2]);\n        Serial.print(\" qz = \"); Serial.println(q[3]);\n    */\n    // Define output variables from updated quaternion---these are Tait-Bryan angles, commonly used in aircraft orientation.\n    // In this coordinate system, the positive z-axis is down toward Earth.\n    // Yaw is the angle between Sensor x-axis and Earth magnetic North (or true North if corrected for local declination, looking down on the sensor positive yaw is counterclockwise.\n    // Pitch is angle between sensor x-axis and Earth ground plane, toward the Earth is positive, up toward the sky is negative.\n    // Roll is angle between sensor y-axis and Earth ground plane, y-axis up is positive roll.\n    // These arise from the definition of the homogeneous rotation matrix constructed from quaternions.\n    // Tait-Bryan angles as well as Euler angles are non-commutative; that is, the get the correct orientation the rotations must be\n    // applied in the correct order which for this configuration is yaw, pitch, and then roll.\n    // For more see http://en.wikipedia.org/wiki/Conversion_between_quaternions_and_Euler_angles which has additional links.\n    yaw   = atan2(2.0f * (q[1] * q[2] + q[0] * q[3]), q[0] * q[0] + q[1] * q[1] - q[2] * q[2] - q[3] * q[3]);\n    pitch = -asin(2.0f * (q[1] * q[3] - q[0] * q[2]));\n    roll  = atan2(2.0f * (q[0] * q[1] + q[2] * q[3]), q[0] * q[0] - q[1] * q[1] - q[2] * q[2] + q[3] * q[3]);\n\n    pitch *= 180.0f / PI;\n    yaw   *= 180.0f / PI;\n    roll  *= 180.0f / PI;\n\n    Serial.print(\"Yaw, Pitch, Roll: \");\n    Serial.print(yaw, 2);\n    Serial.print(\", \");\n    Serial.print(pitch, 2);\n    Serial.print(\", \");\n    Serial.println(roll, 2);\n\n    //    Serial.print(\"average rate = \"); Serial.print(1.0f/deltat, 2); Serial.println(\" Hz\");\n\n    Serial.println(\" x\\t  y\\t  z  \");\n\n    Serial.print((int)(1000 * ax)); Serial.print('\\t');\n    Serial.print((int)(1000 * ay)); Serial.print('\\t');\n    Serial.print((int)(1000 * az));\n    Serial.println(\" mg\");\n\n    Serial.print((int)(gyrox)); Serial.print('\\t');\n    Serial.print((int)(gyroy)); Serial.print('\\t');\n    Serial.print((int)(gyroz));\n    Serial.println(\" o/s\");\n\n    Serial.print((int)(yaw)); Serial.print('\\t');\n    Serial.print((int)(pitch)); Serial.print('\\t');\n    Serial.print((int)(roll));\n    Serial.println(\" ypr\");\n\n    Serial.print(\"rt: \"); Serial.print(1.0f / deltat, 2); Serial.println(\" Hz\");\n\n    blinkOn = ~blinkOn;\n    count = millis();\n  }\n}\n\n// Implementation of Sebastian Madgwick's \"...efficient orientation filter for... inertial/magnetic sensor arrays\"\n// (see http://www.x-io.co.uk/category/open-source/ for examples and more details)\n// which fuses acceleration and rotation rate to produce a quaternion-based estimate of relative\n// device orientation -- which can be converted to yaw, pitch, and roll. Useful for stabilizing quadcopters, etc.\n// The performance of the orientation filter is at least as good as conventional Kalman-based filtering algorithms\n// but is much less computationally intensive---it can be performed on a 3.3 V Pro Mini operating at 8 MHz!\n        void MadgwickQuaternionUpdate(float ax, float ay, float az, float gyrox, float gyroy, float gyroz)\n        {\n            float q1 = q[0], q2 = q[1], q3 = q[2], q4 = q[3];         // short name local variable for readability\n            float norm;                                               // vector norm\n            float f1, f2, f3;                                         // objetive funcyion elements\n            float J_11or24, J_12or23, J_13or22, J_14or21, J_32, J_33; // objective function Jacobian elements\n            float qDot1, qDot2, qDot3, qDot4;\n            float hatDot1, hatDot2, hatDot3, hatDot4;\n            float gerrx, gerry, gerrz, gbiasx, gbiasy, gbiasz;        // gyro bias error\n\n            // Auxiliary variables to avoid repeated arithmetic\n            float _halfq1 = 0.5f * q1;\n            float _halfq2 = 0.5f * q2;\n            float _halfq3 = 0.5f * q3;\n            float _halfq4 = 0.5f * q4;\n            float _2q1 = 2.0f * q1;\n            float _2q2 = 2.0f * q2;\n            float _2q3 = 2.0f * q3;\n            float _2q4 = 2.0f * q4;\n            float _2q1q3 = 2.0f * q1 * q3;\n            float _2q3q4 = 2.0f * q3 * q4;\n\n            // Normalise accelerometer measurement\n            norm = sqrt(ax * ax + ay * ay + az * az);\n            if (norm == 0.0f) return; // handle NaN\n            norm = 1.0f/norm;\n            ax *= norm;\n            ay *= norm;\n            az *= norm;\n            \n            // Compute the objective function and Jacobian\n            f1 = _2q2 * q4 - _2q1 * q3 - ax;\n            f2 = _2q1 * q2 + _2q3 * q4 - ay;\n            f3 = 1.0f - _2q2 * q2 - _2q3 * q3 - az;\n            J_11or24 = _2q3;\n            J_12or23 = _2q4;\n            J_13or22 = _2q1;\n            J_14or21 = _2q2;\n            J_32 = 2.0f * J_14or21;\n            J_33 = 2.0f * J_11or24;\n          \n            // Compute the gradient (matrix multiplication)\n            hatDot1 = J_14or21 * f2 - J_11or24 * f1;\n            hatDot2 = J_12or23 * f1 + J_13or22 * f2 - J_32 * f3;\n            hatDot3 = J_12or23 * f2 - J_33 *f3 - J_13or22 * f1;\n            hatDot4 = J_14or21 * f1 + J_11or24 * f2;\n            \n            // Normalize the gradient\n            norm = sqrt(hatDot1 * hatDot1 + hatDot2 * hatDot2 + hatDot3 * hatDot3 + hatDot4 * hatDot4);\n            hatDot1 /= norm;\n            hatDot2 /= norm;\n            hatDot3 /= norm;\n            hatDot4 /= norm;\n            \n            // Compute estimated gyroscope biases\n            gerrx = _2q1 * hatDot2 - _2q2 * hatDot1 - _2q3 * hatDot4 + _2q4 * hatDot3;\n            gerry = _2q1 * hatDot3 + _2q2 * hatDot4 - _2q3 * hatDot1 - _2q4 * hatDot2;\n            gerrz = _2q1 * hatDot4 - _2q2 * hatDot3 + _2q3 * hatDot2 - _2q4 * hatDot1;\n            \n            // Compute and remove gyroscope biases\n            gbiasx += gerrx * deltat * zeta;\n            gbiasy += gerry * deltat * zeta;\n            gbiasz += gerrz * deltat * zeta;\n            gyrox -= gbiasx;\n            gyroy -= gbiasy;\n            gyroz -= gbiasz;\n            \n            // Compute the quaternion derivative\n            qDot1 = -_halfq2 * gyrox - _halfq3 * gyroy - _halfq4 * gyroz;\n            qDot2 =  _halfq1 * gyrox + _halfq3 * gyroz - _halfq4 * gyroy;\n            qDot3 =  _halfq1 * gyroy - _halfq2 * gyroz + _halfq4 * gyrox;\n            qDot4 =  _halfq1 * gyroz + _halfq2 * gyroy - _halfq3 * gyrox;\n\n            // Compute then integrate estimated quaternion derivative\n            q1 += (qDot1 -(beta * hatDot1)) * deltat;\n            q2 += (qDot2 -(beta * hatDot2)) * deltat;\n            q3 += (qDot3 -(beta * hatDot3)) * deltat;\n            q4 += (qDot4 -(beta * hatDot4)) * deltat;\n\n            // Normalize the quaternion\n            norm = sqrt(q1 * q1 + q2 * q2 + q3 * q3 + q4 * q4);    // normalise quaternion\n            norm = 1.0f/norm;\n            q[0] = q1 * norm;\n            q[1] = q2 * norm;\n            q[2] = q3 * norm;\n            q[3] = q4 * norm;\n        }\n"
  },
  {
    "path": "README.md",
    "content": "MPU-6050\n========\n\nBasic MPU-6050 Arduino sketch of sensor function\n\nFor a discussion of performance on various microcontroller platforms, uses and limitations of the MPU-6050 see ![here.](https://github.com/kriswiner/MPU-6050/wiki/Affordable-9-DoF-Sensor-Fusion)\n\nI have written a report from the June 11-12, 2014 ![Invensense Developers Conference.](https://github.com/kriswiner/MPU-6050/wiki/2014-Invensense-Developer%27s-Conference)\n\nThis sketch demonstrates  MPU-6050 basic functionality including initialization, accelerometer and gyro calibration, sleep mode functionality as well as parameterizing the register addresses. Added display functions to allow display to on-breadboard monitor. \nNo DMP use. We just want to get out the accelerations, temperature, and gyro readings.\n \nRuns on 3.3V 8 MHz Pro Mini and Teensy 3.1.\n\nAdded quaternion filter based on Madgwick's open-source sensor fusion algorithms. The MPU-6050 lacks a magnetic vector for absolute orientation estimation as is possible with the MPU-9150 or LSM9DS0. This algorithm allows estimation of quaternions and relative orientation, allowing output of Yaw, Pitch, and Roll which is subject to Yaw drift due to gyro bias drift. Despite the inclusion of a gyro bias drift correction component to the sensor fusion algorithm, Yaw drift is about half a degree per minute or less, which is not too bad. In principle, Yaw should not be possible to estimate with only a single absolute reference (gravity down), yet this algorithm does a good job of estimating relative Yaw with good stability over short time scales.\n\nI have ![added](https://github.com/kriswiner/MPU-6050/tree/master/STM32F401) code compiled with the mbed compiler to run 6-axis sensor fusion using the STM32MF401 ARM processor and the MPU-6050.  Why would this be necessary or desirable?\n\nThe filter runs at a  200 Hz update rate on a 3.3 V 8 MHz Pro Mini AVR (Arduino) microcontroller.\n\nThe filter runs at a 3200 Hz update rate on a 3.3 V 96 MHz Teensy 3.1 ARM microcontroller.\n\nThe filter runs at a 5500 Hz update rate on a 3.3 V 84 MHz STM32F401 ARM microcontroller.\n\nOne doesn't need more that about 1000 Hz sensor fusion filter update rate to get optimal performance from 6- and 9-axis motion sensors, but the power consumption is proportional to the microcontroller clock speed. If that 1000 Hz rate can be achieved at a lower clock speed, then lower power consumption can be achieved. This is a critical consideration for portable (wearable) motion sensing and motion control devices.\n\nLet's assume the sensor fusion filter update rate is linearly proportional to the clock speed (a pretty good assumption). Then to get 1000 Hz update rates for the Teensy only requires 96/3.2 = 30 MHz clock speed. In fact, at 24 MHz clock speed the update rate with the Teensy 3.1 is 1365 Hz. For the STM32F401, the clock speed needs to be only 84/5.5 = 16 MHz to reach a sensor fusion filter update rate of 1000 Hz. In practice, the clock speeds are not arbitrary but must meet certain constraints; it might not be possible to run the STM32F401 at such a low speed. So far, I have only run it at 84 and 42 MHz; at 42 MHz I got sensor fusion filter update rates of ~4400 Hz. It appears that the STM32F401 would require less than half the power compared to the Teensy 3.1 to achieve the same level of sensor fusion performance. Meaning that all else being equal (it never is!), a wearable device using the STM32F401 as the microcontroller could last twice as long before battery change or charging is required. This is a major commercial advantage and why the STM32 M4 Cortex family of processors is so interesting.\n"
  },
  {
    "path": "STM32F401/MPU6050.h",
    "content": "#ifndef MPU6050_H\n#define MPU6050_H\n \n#include \"mbed.h\"\n#include \"math.h\"\n \n // Define registers per MPU6050, Register Map and Descriptions, Rev 4.2, 08/19/2013 6 DOF Motion sensor fusion device\n// Invensense Inc., www.invensense.com\n// See also MPU-6050 Register Map and Descriptions, Revision 4.0, RM-MPU-6050A-00, 9/12/2012 for registers not listed in \n// above document; the MPU6050 and MPU 9150 are virtually identical but the latter has an on-board magnetic sensor\n//\n#define XGOFFS_TC        0x00 // Bit 7 PWR_MODE, bits 6:1 XG_OFFS_TC, bit 0 OTP_BNK_VLD                 \n#define YGOFFS_TC        0x01                                                                          \n#define ZGOFFS_TC        0x02\n#define X_FINE_GAIN      0x03 // [7:0] fine gain\n#define Y_FINE_GAIN      0x04\n#define Z_FINE_GAIN      0x05\n#define XA_OFFSET_H      0x06 // User-defined trim values for accelerometer\n#define XA_OFFSET_L_TC   0x07\n#define YA_OFFSET_H      0x08\n#define YA_OFFSET_L_TC   0x09\n#define ZA_OFFSET_H      0x0A\n#define ZA_OFFSET_L_TC   0x0B\n#define SELF_TEST_X      0x0D\n#define SELF_TEST_Y      0x0E    \n#define SELF_TEST_Z      0x0F\n#define SELF_TEST_A      0x10\n#define XG_OFFS_USRH     0x13  // User-defined trim values for gyroscope; supported in MPU-6050?\n#define XG_OFFS_USRL     0x14\n#define YG_OFFS_USRH     0x15\n#define YG_OFFS_USRL     0x16\n#define ZG_OFFS_USRH     0x17\n#define ZG_OFFS_USRL     0x18\n#define SMPLRT_DIV       0x19\n#define CONFIG           0x1A\n#define GYRO_CONFIG      0x1B\n#define ACCEL_CONFIG     0x1C\n#define FF_THR           0x1D  // Free-fall\n#define FF_DUR           0x1E  // Free-fall\n#define MOT_THR          0x1F  // Motion detection threshold bits [7:0]\n#define MOT_DUR          0x20  // Duration counter threshold for motion interrupt generation, 1 kHz rate, LSB = 1 ms\n#define ZMOT_THR         0x21  // Zero-motion detection threshold bits [7:0]\n#define ZRMOT_DUR        0x22  // Duration counter threshold for zero motion interrupt generation, 16 Hz rate, LSB = 64 ms\n#define FIFO_EN          0x23\n#define I2C_MST_CTRL     0x24   \n#define I2C_SLV0_ADDR    0x25\n#define I2C_SLV0_REG     0x26\n#define I2C_SLV0_CTRL    0x27\n#define I2C_SLV1_ADDR    0x28\n#define I2C_SLV1_REG     0x29\n#define I2C_SLV1_CTRL    0x2A\n#define I2C_SLV2_ADDR    0x2B\n#define I2C_SLV2_REG     0x2C\n#define I2C_SLV2_CTRL    0x2D\n#define I2C_SLV3_ADDR    0x2E\n#define I2C_SLV3_REG     0x2F\n#define I2C_SLV3_CTRL    0x30\n#define I2C_SLV4_ADDR    0x31\n#define I2C_SLV4_REG     0x32\n#define I2C_SLV4_DO      0x33\n#define I2C_SLV4_CTRL    0x34\n#define I2C_SLV4_DI      0x35\n#define I2C_MST_STATUS   0x36\n#define INT_PIN_CFG      0x37\n#define INT_ENABLE       0x38\n#define DMP_INT_STATUS   0x39  // Check DMP interrupt\n#define INT_STATUS       0x3A\n#define ACCEL_XOUT_H     0x3B\n#define ACCEL_XOUT_L     0x3C\n#define ACCEL_YOUT_H     0x3D\n#define ACCEL_YOUT_L     0x3E\n#define ACCEL_ZOUT_H     0x3F\n#define ACCEL_ZOUT_L     0x40\n#define TEMP_OUT_H       0x41\n#define TEMP_OUT_L       0x42\n#define GYRO_XOUT_H      0x43\n#define GYRO_XOUT_L      0x44\n#define GYRO_YOUT_H      0x45\n#define GYRO_YOUT_L      0x46\n#define GYRO_ZOUT_H      0x47\n#define GYRO_ZOUT_L      0x48\n#define EXT_SENS_DATA_00 0x49\n#define EXT_SENS_DATA_01 0x4A\n#define EXT_SENS_DATA_02 0x4B\n#define EXT_SENS_DATA_03 0x4C\n#define EXT_SENS_DATA_04 0x4D\n#define EXT_SENS_DATA_05 0x4E\n#define EXT_SENS_DATA_06 0x4F\n#define EXT_SENS_DATA_07 0x50\n#define EXT_SENS_DATA_08 0x51\n#define EXT_SENS_DATA_09 0x52\n#define EXT_SENS_DATA_10 0x53\n#define EXT_SENS_DATA_11 0x54\n#define EXT_SENS_DATA_12 0x55\n#define EXT_SENS_DATA_13 0x56\n#define EXT_SENS_DATA_14 0x57\n#define EXT_SENS_DATA_15 0x58\n#define EXT_SENS_DATA_16 0x59\n#define EXT_SENS_DATA_17 0x5A\n#define EXT_SENS_DATA_18 0x5B\n#define EXT_SENS_DATA_19 0x5C\n#define EXT_SENS_DATA_20 0x5D\n#define EXT_SENS_DATA_21 0x5E\n#define EXT_SENS_DATA_22 0x5F\n#define EXT_SENS_DATA_23 0x60\n#define MOT_DETECT_STATUS 0x61\n#define I2C_SLV0_DO      0x63\n#define I2C_SLV1_DO      0x64\n#define I2C_SLV2_DO      0x65\n#define I2C_SLV3_DO      0x66\n#define I2C_MST_DELAY_CTRL 0x67\n#define SIGNAL_PATH_RESET  0x68\n#define MOT_DETECT_CTRL   0x69\n#define USER_CTRL        0x6A  // Bit 7 enable DMP, bit 3 reset DMP\n#define PWR_MGMT_1       0x6B // Device defaults to the SLEEP mode\n#define PWR_MGMT_2       0x6C\n#define DMP_BANK         0x6D  // Activates a specific bank in the DMP\n#define DMP_RW_PNT       0x6E  // Set read/write pointer to a specific start address in specified DMP bank\n#define DMP_REG          0x6F  // Register in DMP from which to read or to which to write\n#define DMP_REG_1        0x70\n#define DMP_REG_2        0x71\n#define FIFO_COUNTH      0x72\n#define FIFO_COUNTL      0x73\n#define FIFO_R_W         0x74\n#define WHO_AM_I_MPU6050 0x75 // Should return 0x68\n\n// Using the GY-521 breakout board, I set ADO to 0 by grounding through a 4k7 resistor\n// Seven-bit device address is 110100 for ADO = 0 and 110101 for ADO = 1\n#define ADO 0\n#if ADO\n#define MPU6050_ADDRESS 0x69<<1  // Device address when ADO = 1\n#else\n#define MPU6050_ADDRESS 0x68<<1  // Device address when ADO = 0\n#endif\n\n// Set initial input parameters\nenum Ascale {\n  AFS_2G = 0,\n  AFS_4G,\n  AFS_8G,\n  AFS_16G\n};\n\nenum Gscale {\n  GFS_250DPS = 0,\n  GFS_500DPS,\n  GFS_1000DPS,\n  GFS_2000DPS\n};\n\n// Specify sensor full scale\nint Gscale = GFS_250DPS;\nint Ascale = AFS_2G;\n\n//Set up I2C, (SDA,SCL)\nI2C i2c(I2C_SDA, I2C_SCL);\n\nDigitalOut myled(LED1);\n   \nfloat aRes, gRes; // scale resolutions per LSB for the sensors\n  \n// Pin definitions\nint intPin = 12;  // These can be changed, 2 and 3 are the Arduinos ext int pins\n\nint16_t accelCount[3];  // Stores the 16-bit signed accelerometer sensor output\nfloat ax, ay, az;       // Stores the real accel value in g's\nint16_t gyroCount[3];   // Stores the 16-bit signed gyro sensor output\nfloat gx, gy, gz;       // Stores the real gyro value in degrees per seconds\nfloat gyroBias[3] = {0, 0, 0}, accelBias[3] = {0, 0, 0}; // Bias corrections for gyro and accelerometer\nint16_t tempCount;   // Stores the real internal chip temperature in degrees Celsius\nfloat temperature;\nfloat SelfTest[6];\n\nint delt_t = 0; // used to control display output rate\nint count = 0;  // used to control display output rate\n\n// parameters for 6 DoF sensor fusion calculations\nfloat PI = 3.14159265358979323846f;\nfloat GyroMeasError = PI * (60.0f / 180.0f);     // gyroscope measurement error in rads/s (start at 60 deg/s), then reduce after ~10 s to 3\nfloat beta = sqrt(3.0f / 4.0f) * GyroMeasError;  // compute beta\nfloat GyroMeasDrift = PI * (1.0f / 180.0f);      // gyroscope measurement drift in rad/s/s (start at 0.0 deg/s/s)\nfloat zeta = sqrt(3.0f / 4.0f) * GyroMeasDrift;  // compute zeta, the other free parameter in the Madgwick scheme usually set to a small or zero value\nfloat pitch, yaw, roll;\nfloat deltat = 0.0f;                              // integration interval for both filter schemes\nint lastUpdate = 0, firstUpdate = 0, Now = 0;     // used to calculate integration interval                               // used to calculate integration interval\nfloat q[4] = {1.0f, 0.0f, 0.0f, 0.0f};            // vector to hold quaternion\n\nclass MPU6050 {\n \n    protected:\n \n    public:\n  //===================================================================================================================\n//====== Set of useful function to access acceleratio, gyroscope, and temperature data\n//===================================================================================================================\n\n    void writeByte(uint8_t address, uint8_t subAddress, uint8_t data)\n{\n   char data_write[2];\n   data_write[0] = subAddress;\n   data_write[1] = data;\n   i2c.write(address, data_write, 2, 0);\n}\n\n    char readByte(uint8_t address, uint8_t subAddress)\n{\n    char data[1]; // `data` will store the register data     \n    char data_write[1];\n    data_write[0] = subAddress;\n    i2c.write(address, data_write, 1, 1); // no stop\n    i2c.read(address, data, 1, 0); \n    return data[0]; \n}\n\n    void readBytes(uint8_t address, uint8_t subAddress, uint8_t count, uint8_t * dest)\n{     \n    char data[14];\n    char data_write[1];\n    data_write[0] = subAddress;\n    i2c.write(address, data_write, 1, 1); // no stop\n    i2c.read(address, data, count, 0); \n    for(int ii = 0; ii < count; ii++) {\n     dest[ii] = data[ii];\n    }\n} \n \n\nvoid getGres() {\n  switch (Gscale)\n  {\n    // Possible gyro scales (and their register bit settings) are:\n    // 250 DPS (00), 500 DPS (01), 1000 DPS (10), and 2000 DPS  (11). \n        // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:\n    case GFS_250DPS:\n          gRes = 250.0/32768.0;\n          break;\n    case GFS_500DPS:\n          gRes = 500.0/32768.0;\n          break;\n    case GFS_1000DPS:\n          gRes = 1000.0/32768.0;\n          break;\n    case GFS_2000DPS:\n          gRes = 2000.0/32768.0;\n          break;\n  }\n}\n\nvoid getAres() {\n  switch (Ascale)\n  {\n    // Possible accelerometer scales (and their register bit settings) are:\n    // 2 Gs (00), 4 Gs (01), 8 Gs (10), and 16 Gs  (11). \n        // Here's a bit of an algorith to calculate DPS/(ADC tick) based on that 2-bit value:\n    case AFS_2G:\n          aRes = 2.0/32768.0;\n          break;\n    case AFS_4G:\n          aRes = 4.0/32768.0;\n          break;\n    case AFS_8G:\n          aRes = 8.0/32768.0;\n          break;\n    case AFS_16G:\n          aRes = 16.0/32768.0;\n          break;\n  }\n}\n\n\nvoid readAccelData(int16_t * destination)\n{\n  uint8_t rawData[6];  // x/y/z accel register data stored here\n  readBytes(MPU6050_ADDRESS, ACCEL_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers into data array\n  destination[0] = (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value\n  destination[1] = (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;  \n  destination[2] = (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ; \n}\n\nvoid readGyroData(int16_t * destination)\n{\n  uint8_t rawData[6];  // x/y/z gyro register data stored here\n  readBytes(MPU6050_ADDRESS, GYRO_XOUT_H, 6, &rawData[0]);  // Read the six raw data registers sequentially into data array\n  destination[0] = (int16_t)(((int16_t)rawData[0] << 8) | rawData[1]) ;  // Turn the MSB and LSB into a signed 16-bit value\n  destination[1] = (int16_t)(((int16_t)rawData[2] << 8) | rawData[3]) ;  \n  destination[2] = (int16_t)(((int16_t)rawData[4] << 8) | rawData[5]) ; \n}\n\nint16_t readTempData()\n{\n  uint8_t rawData[2];  // x/y/z gyro register data stored here\n  readBytes(MPU6050_ADDRESS, TEMP_OUT_H, 2, &rawData[0]);  // Read the two raw data registers sequentially into data array \n  return (int16_t)(((int16_t)rawData[0]) << 8 | rawData[1]) ;  // Turn the MSB and LSB into a 16-bit value\n}\n\n\n\n// Configure the motion detection control for low power accelerometer mode\nvoid LowPowerAccelOnly()\n{\n\n// The sensor has a high-pass filter necessary to invoke to allow the sensor motion detection algorithms work properly\n// Motion detection occurs on free-fall (acceleration below a threshold for some time for all axes), motion (acceleration\n// above a threshold for some time on at least one axis), and zero-motion toggle (acceleration on each axis less than a \n// threshold for some time sets this flag, motion above the threshold turns it off). The high-pass filter takes gravity out\n// consideration for these threshold evaluations; otherwise, the flags would be set all the time!\n  \n  uint8_t c = readByte(MPU6050_ADDRESS, PWR_MGMT_1);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c & ~0x30); // Clear sleep and cycle bits [5:6]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c |  0x30); // Set sleep and cycle bits [5:6] to zero to make sure accelerometer is running\n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_2);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c & ~0x38); // Clear standby XA, YA, and ZA bits [3:5]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c |  0x00); // Set XA, YA, and ZA bits [3:5] to zero to make sure accelerometer is running\n    \n  c = readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x07); // Clear high-pass filter bits [2:0]\n// Set high-pass filter to 0) reset (disable), 1) 5 Hz, 2) 2.5 Hz, 3) 1.25 Hz, 4) 0.63 Hz, or 7) Hold\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG,  c | 0x00);  // Set ACCEL_HPF to 0; reset mode disbaling high-pass filter\n\n  c = readByte(MPU6050_ADDRESS, CONFIG);\n  writeByte(MPU6050_ADDRESS, CONFIG, c & ~0x07); // Clear low-pass filter bits [2:0]\n  writeByte(MPU6050_ADDRESS, CONFIG, c |  0x00);  // Set DLPD_CFG to 0; 260 Hz bandwidth, 1 kHz rate\n    \n  c = readByte(MPU6050_ADDRESS, INT_ENABLE);\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, c & ~0xFF);  // Clear all interrupts\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x40);  // Enable motion threshold (bits 5) interrupt only\n  \n// Motion detection interrupt requires the absolute value of any axis to lie above the detection threshold\n// for at least the counter duration\n  writeByte(MPU6050_ADDRESS, MOT_THR, 0x80); // Set motion detection to 0.256 g; LSB = 2 mg\n  writeByte(MPU6050_ADDRESS, MOT_DUR, 0x01); // Set motion detect duration to 1  ms; LSB is 1 ms @ 1 kHz rate\n  \n  wait(0.1);  // Add delay for accumulation of samples\n  \n  c = readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x07); // Clear high-pass filter bits [2:0]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c |  0x07);  // Set ACCEL_HPF to 7; hold the initial accleration value as a referance\n   \n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_2);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c & ~0xC7); // Clear standby XA, YA, and ZA bits [3:5] and LP_WAKE_CTRL bits [6:7]\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, c |  0x47); // Set wakeup frequency to 5 Hz, and disable XG, YG, and ZG gyros (bits [0:2])  \n\n  c = readByte(MPU6050_ADDRESS, PWR_MGMT_1);\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c & ~0x20); // Clear sleep and cycle bit 5\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, c |  0x20); // Set cycle bit 5 to begin low power accelerometer motion interrupts\n\n}\n\n\nvoid resetMPU6050() {\n  // reset device\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device\n  wait(0.1);\n  }\n  \n  \nvoid initMPU6050()\n{  \n // Initialize MPU6050 device\n // wake up device\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x00); // Clear sleep mode bit (6), enable all sensors \n  wait(0.1); // Delay 100 ms for PLL to get established on x-axis gyro; should check for PLL ready interrupt  \n\n // get stable time source\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x01);  // Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001\n\n // Configure Gyro and Accelerometer\n // Disable FSYNC and set accelerometer and gyro bandwidth to 44 and 42 Hz, respectively; \n // DLPF_CFG = bits 2:0 = 010; this sets the sample rate at 1 kHz for both\n // Maximum delay is 4.9 ms which is just over a 200 Hz maximum rate\n  writeByte(MPU6050_ADDRESS, CONFIG, 0x03);  \n \n // Set sample rate = gyroscope output rate/(1 + SMPLRT_DIV)\n  writeByte(MPU6050_ADDRESS, SMPLRT_DIV, 0x04);  // Use a 200 Hz rate; the same rate set in CONFIG above\n \n // Set gyroscope full scale range\n // Range selects FS_SEL and AFS_SEL are 0 - 3, so 2-bit values are left-shifted into positions 4:3\n  uint8_t c =  readByte(MPU6050_ADDRESS, GYRO_CONFIG);\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c & ~0xE0); // Clear self-test bits [7:5] \n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c & ~0x18); // Clear AFS bits [4:3]\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, c | Gscale << 3); // Set full scale range for the gyro\n   \n // Set accelerometer configuration\n  c =  readByte(MPU6050_ADDRESS, ACCEL_CONFIG);\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0xE0); // Clear self-test bits [7:5] \n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c & ~0x18); // Clear AFS bits [4:3]\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, c | Ascale << 3); // Set full scale range for the accelerometer \n\n  // Configure Interrupts and Bypass Enable\n  // Set interrupt pin active high, push-pull, and clear on read of INT_STATUS, enable I2C_BYPASS_EN so additional chips \n  // can join the I2C bus and all can be controlled by the Arduino as master\n   writeByte(MPU6050_ADDRESS, INT_PIN_CFG, 0x22);    \n   writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x01);  // Enable data ready (bit 0) interrupt\n}\n\n// Function which accumulates gyro and accelerometer data after device initialization. It calculates the average\n// of the at-rest readings and then loads the resulting offsets into accelerometer and gyro bias registers.\nvoid calibrateMPU6050(float * dest1, float * dest2)\n{  \n  uint8_t data[12]; // data array to hold accelerometer and gyro x, y, z, data\n  uint16_t ii, packet_count, fifo_count;\n  int32_t gyro_bias[3] = {0, 0, 0}, accel_bias[3] = {0, 0, 0};\n  \n// reset device, reset all registers, clear gyro and accelerometer bias registers\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x80); // Write a one to bit 7 reset bit; toggle reset device\n  wait(0.1);  \n   \n// get stable time source\n// Set clock source to be PLL with x-axis gyroscope reference, bits 2:0 = 001\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x01);  \n  writeByte(MPU6050_ADDRESS, PWR_MGMT_2, 0x00); \n  wait(0.2);\n  \n// Configure device for bias calculation\n  writeByte(MPU6050_ADDRESS, INT_ENABLE, 0x00);   // Disable all interrupts\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x00);      // Disable FIFO\n  writeByte(MPU6050_ADDRESS, PWR_MGMT_1, 0x00);   // Turn on internal clock source\n  writeByte(MPU6050_ADDRESS, I2C_MST_CTRL, 0x00); // Disable I2C master\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x00);    // Disable FIFO and I2C master modes\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x0C);    // Reset FIFO and DMP\n  wait(0.015);\n  \n// Configure MPU6050 gyro and accelerometer for bias calculation\n  writeByte(MPU6050_ADDRESS, CONFIG, 0x01);      // Set low-pass filter to 188 Hz\n  writeByte(MPU6050_ADDRESS, SMPLRT_DIV, 0x00);  // Set sample rate to 1 kHz\n  writeByte(MPU6050_ADDRESS, GYRO_CONFIG, 0x00);  // Set gyro full-scale to 250 degrees per second, maximum sensitivity\n  writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, 0x00); // Set accelerometer full-scale to 2 g, maximum sensitivity\n \n  uint16_t  gyrosensitivity  = 131;   // = 131 LSB/degrees/sec\n  uint16_t  accelsensitivity = 16384;  // = 16384 LSB/g\n\n// Configure FIFO to capture accelerometer and gyro data for bias calculation\n  writeByte(MPU6050_ADDRESS, USER_CTRL, 0x40);   // Enable FIFO  \n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x78);     // Enable gyro and accelerometer sensors for FIFO  (max size 1024 bytes in MPU-6050)\n  wait(0.08); // accumulate 80 samples in 80 milliseconds = 960 bytes\n\n// At end of sample accumulation, turn off FIFO sensor read\n  writeByte(MPU6050_ADDRESS, FIFO_EN, 0x00);        // Disable gyro and accelerometer sensors for FIFO\n  readBytes(MPU6050_ADDRESS, FIFO_COUNTH, 2, &data[0]); // read FIFO sample count\n  fifo_count = ((uint16_t)data[0] << 8) | data[1];\n  packet_count = fifo_count/12;// How many sets of full gyro and accelerometer data for averaging\n\n  for (ii = 0; ii < packet_count; ii++) {\n    int16_t accel_temp[3] = {0, 0, 0}, gyro_temp[3] = {0, 0, 0};\n    readBytes(MPU6050_ADDRESS, FIFO_R_W, 12, &data[0]); // read data for averaging\n    accel_temp[0] = (int16_t) (((int16_t)data[0] << 8) | data[1]  ) ;  // Form signed 16-bit integer for each sample in FIFO\n    accel_temp[1] = (int16_t) (((int16_t)data[2] << 8) | data[3]  ) ;\n    accel_temp[2] = (int16_t) (((int16_t)data[4] << 8) | data[5]  ) ;    \n    gyro_temp[0]  = (int16_t) (((int16_t)data[6] << 8) | data[7]  ) ;\n    gyro_temp[1]  = (int16_t) (((int16_t)data[8] << 8) | data[9]  ) ;\n    gyro_temp[2]  = (int16_t) (((int16_t)data[10] << 8) | data[11]) ;\n    \n    accel_bias[0] += (int32_t) accel_temp[0]; // Sum individual signed 16-bit biases to get accumulated signed 32-bit biases\n    accel_bias[1] += (int32_t) accel_temp[1];\n    accel_bias[2] += (int32_t) accel_temp[2];\n    gyro_bias[0]  += (int32_t) gyro_temp[0];\n    gyro_bias[1]  += (int32_t) gyro_temp[1];\n    gyro_bias[2]  += (int32_t) gyro_temp[2];\n            \n}\n    accel_bias[0] /= (int32_t) packet_count; // Normalize sums to get average count biases\n    accel_bias[1] /= (int32_t) packet_count;\n    accel_bias[2] /= (int32_t) packet_count;\n    gyro_bias[0]  /= (int32_t) packet_count;\n    gyro_bias[1]  /= (int32_t) packet_count;\n    gyro_bias[2]  /= (int32_t) packet_count;\n    \n  if(accel_bias[2] > 0L) {accel_bias[2] -= (int32_t) accelsensitivity;}  // Remove gravity from the z-axis accelerometer bias calculation\n  else {accel_bias[2] += (int32_t) accelsensitivity;}\n \n// Construct the gyro biases for push to the hardware gyro bias registers, which are reset to zero upon device startup\n  data[0] = (-gyro_bias[0]/4  >> 8) & 0xFF; // Divide by 4 to get 32.9 LSB per deg/s to conform to expected bias input format\n  data[1] = (-gyro_bias[0]/4)       & 0xFF; // Biases are additive, so change sign on calculated average gyro biases\n  data[2] = (-gyro_bias[1]/4  >> 8) & 0xFF;\n  data[3] = (-gyro_bias[1]/4)       & 0xFF;\n  data[4] = (-gyro_bias[2]/4  >> 8) & 0xFF;\n  data[5] = (-gyro_bias[2]/4)       & 0xFF;\n\n// Push gyro biases to hardware registers\n  writeByte(MPU6050_ADDRESS, XG_OFFS_USRH, data[0]); \n  writeByte(MPU6050_ADDRESS, XG_OFFS_USRL, data[1]);\n  writeByte(MPU6050_ADDRESS, YG_OFFS_USRH, data[2]);\n  writeByte(MPU6050_ADDRESS, YG_OFFS_USRL, data[3]);\n  writeByte(MPU6050_ADDRESS, ZG_OFFS_USRH, data[4]);\n  writeByte(MPU6050_ADDRESS, ZG_OFFS_USRL, data[5]);\n\n  dest1[0] = (float) gyro_bias[0]/(float) gyrosensitivity; // construct gyro bias in deg/s for later manual subtraction\n  dest1[1] = (float) gyro_bias[1]/(float) gyrosensitivity;\n  dest1[2] = (float) gyro_bias[2]/(float) gyrosensitivity;\n\n// Construct the accelerometer biases for push to the hardware accelerometer bias registers. These registers contain\n// factory trim values which must be added to the calculated accelerometer biases; on boot up these registers will hold\n// non-zero values. In addition, bit 0 of the lower byte must be preserved since it is used for temperature\n// compensation calculations. Accelerometer bias registers expect bias input as 2048 LSB per g, so that\n// the accelerometer biases calculated above must be divided by 8.\n\n  int32_t accel_bias_reg[3] = {0, 0, 0}; // A place to hold the factory accelerometer trim biases\n  readBytes(MPU6050_ADDRESS, XA_OFFSET_H, 2, &data[0]); // Read factory accelerometer trim values\n  accel_bias_reg[0] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  readBytes(MPU6050_ADDRESS, YA_OFFSET_H, 2, &data[0]);\n  accel_bias_reg[1] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  readBytes(MPU6050_ADDRESS, ZA_OFFSET_H, 2, &data[0]);\n  accel_bias_reg[2] = (int16_t) ((int16_t)data[0] << 8) | data[1];\n  \n  uint32_t mask = 1uL; // Define mask for temperature compensation bit 0 of lower byte of accelerometer bias registers\n  uint8_t mask_bit[3] = {0, 0, 0}; // Define array to hold mask bit for each accelerometer bias axis\n  \n  for(ii = 0; ii < 3; ii++) {\n    if(accel_bias_reg[ii] & mask) mask_bit[ii] = 0x01; // If temperature compensation bit is set, record that fact in mask_bit\n  }\n\n  // Construct total accelerometer bias, including calculated average accelerometer bias from above\n  accel_bias_reg[0] -= (accel_bias[0]/8); // Subtract calculated averaged accelerometer bias scaled to 2048 LSB/g (16 g full scale)\n  accel_bias_reg[1] -= (accel_bias[1]/8);\n  accel_bias_reg[2] -= (accel_bias[2]/8);\n \n  data[0] = (accel_bias_reg[0] >> 8) & 0xFF;\n  data[1] = (accel_bias_reg[0])      & 0xFF;\n  data[1] = data[1] | mask_bit[0]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n  data[2] = (accel_bias_reg[1] >> 8) & 0xFF;\n  data[3] = (accel_bias_reg[1])      & 0xFF;\n  data[3] = data[3] | mask_bit[1]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n  data[4] = (accel_bias_reg[2] >> 8) & 0xFF;\n  data[5] = (accel_bias_reg[2])      & 0xFF;\n  data[5] = data[5] | mask_bit[2]; // preserve temperature compensation bit when writing back to accelerometer bias registers\n\n  // Push accelerometer biases to hardware registers\n//  writeByte(MPU6050_ADDRESS, XA_OFFSET_H, data[0]);  \n//  writeByte(MPU6050_ADDRESS, XA_OFFSET_L_TC, data[1]);\n//  writeByte(MPU6050_ADDRESS, YA_OFFSET_H, data[2]);\n//  writeByte(MPU6050_ADDRESS, YA_OFFSET_L_TC, data[3]);  \n//  writeByte(MPU6050_ADDRESS, ZA_OFFSET_H, data[4]);\n//  writeByte(MPU6050_ADDRESS, ZA_OFFSET_L_TC, data[5]);\n\n// Output scaled accelerometer biases for manual subtraction in the main program\n   dest2[0] = (float)accel_bias[0]/(float)accelsensitivity; \n   dest2[1] = (float)accel_bias[1]/(float)accelsensitivity;\n   dest2[2] = (float)accel_bias[2]/(float)accelsensitivity;\n}\n\n\n// Accelerometer and gyroscope self test; check calibration wrt factory settings\nvoid MPU6050SelfTest(float * destination) // Should return percent deviation from factory trim values, +/- 14 or less deviation is a pass\n{\n   uint8_t rawData[4] = {0, 0, 0, 0};\n   uint8_t selfTest[6];\n   float factoryTrim[6];\n   \n   // Configure the accelerometer for self-test\n   writeByte(MPU6050_ADDRESS, ACCEL_CONFIG, 0xF0); // Enable self test on all three axes and set accelerometer range to +/- 8 g\n   writeByte(MPU6050_ADDRESS, GYRO_CONFIG,  0xE0); // Enable self test on all three axes and set gyro range to +/- 250 degrees/s\n   wait(0.25);  // Delay a while to let the device execute the self-test\n   rawData[0] = readByte(MPU6050_ADDRESS, SELF_TEST_X); // X-axis self-test results\n   rawData[1] = readByte(MPU6050_ADDRESS, SELF_TEST_Y); // Y-axis self-test results\n   rawData[2] = readByte(MPU6050_ADDRESS, SELF_TEST_Z); // Z-axis self-test results\n   rawData[3] = readByte(MPU6050_ADDRESS, SELF_TEST_A); // Mixed-axis self-test results\n   // Extract the acceleration test results first\n   selfTest[0] = (rawData[0] >> 3) | (rawData[3] & 0x30) >> 4 ; // XA_TEST result is a five-bit unsigned integer\n   selfTest[1] = (rawData[1] >> 3) | (rawData[3] & 0x0C) >> 2 ; // YA_TEST result is a five-bit unsigned integer\n   selfTest[2] = (rawData[2] >> 3) | (rawData[3] & 0x03) >> 0 ; // ZA_TEST result is a five-bit unsigned integer\n   // Extract the gyration test results first\n   selfTest[3] = rawData[0]  & 0x1F ; // XG_TEST result is a five-bit unsigned integer\n   selfTest[4] = rawData[1]  & 0x1F ; // YG_TEST result is a five-bit unsigned integer\n   selfTest[5] = rawData[2]  & 0x1F ; // ZG_TEST result is a five-bit unsigned integer   \n   // Process results to allow final comparison with factory set values\n   factoryTrim[0] = (4096.0f*0.34f)*(pow( (0.92f/0.34f) , ((selfTest[0] - 1.0f)/30.0f))); // FT[Xa] factory trim calculation\n   factoryTrim[1] = (4096.0f*0.34f)*(pow( (0.92f/0.34f) , ((selfTest[1] - 1.0f)/30.0f))); // FT[Ya] factory trim calculation\n   factoryTrim[2] = (4096.0f*0.34f)*(pow( (0.92f/0.34f) , ((selfTest[2] - 1.0f)/30.0f))); // FT[Za] factory trim calculation\n   factoryTrim[3] =  ( 25.0f*131.0f)*(pow( 1.046f , (selfTest[3] - 1.0f) ));             // FT[Xg] factory trim calculation\n   factoryTrim[4] =  (-25.0f*131.0f)*(pow( 1.046f , (selfTest[4] - 1.0f) ));             // FT[Yg] factory trim calculation\n   factoryTrim[5] =  ( 25.0f*131.0f)*(pow( 1.046f , (selfTest[5] - 1.0f) ));             // FT[Zg] factory trim calculation\n   \n //  Output self-test results and factory trim calculation if desired\n //  Serial.println(selfTest[0]); Serial.println(selfTest[1]); Serial.println(selfTest[2]);\n //  Serial.println(selfTest[3]); Serial.println(selfTest[4]); Serial.println(selfTest[5]);\n //  Serial.println(factoryTrim[0]); Serial.println(factoryTrim[1]); Serial.println(factoryTrim[2]);\n //  Serial.println(factoryTrim[3]); Serial.println(factoryTrim[4]); Serial.println(factoryTrim[5]);\n\n // Report results as a ratio of (STR - FT)/FT; the change from Factory Trim of the Self-Test Response\n // To get to percent, must multiply by 100 and subtract result from 100\n   for (int i = 0; i < 6; i++) {\n     destination[i] = 100.0f + 100.0f*(selfTest[i] - factoryTrim[i])/factoryTrim[i]; // Report percent differences\n   }\n   \n}\n\n\n// Implementation of Sebastian Madgwick's \"...efficient orientation filter for... inertial/magnetic sensor arrays\"\n// (see http://www.x-io.co.uk/category/open-source/ for examples and more details)\n// which fuses acceleration and rotation rate to produce a quaternion-based estimate of relative\n// device orientation -- which can be converted to yaw, pitch, and roll. Useful for stabilizing quadcopters, etc.\n// The performance of the orientation filter is at least as good as conventional Kalman-based filtering algorithms\n// but is much less computationally intensive---it can be performed on a 3.3 V Pro Mini operating at 8 MHz!\n        void MadgwickQuaternionUpdate(float ax, float ay, float az, float gx, float gy, float gz)\n        {\n            float q1 = q[0], q2 = q[1], q3 = q[2], q4 = q[3];         // short name local variable for readability\n            float norm;                                               // vector norm\n            float f1, f2, f3;                                         // objective funcyion elements\n            float J_11or24, J_12or23, J_13or22, J_14or21, J_32, J_33; // objective function Jacobian elements\n            float qDot1, qDot2, qDot3, qDot4;\n            float hatDot1, hatDot2, hatDot3, hatDot4;\n            float gerrx, gerry, gerrz, gbiasx, gbiasy, gbiasz;  // gyro bias error\n\n            // Auxiliary variables to avoid repeated arithmetic\n            float _halfq1 = 0.5f * q1;\n            float _halfq2 = 0.5f * q2;\n            float _halfq3 = 0.5f * q3;\n            float _halfq4 = 0.5f * q4;\n            float _2q1 = 2.0f * q1;\n            float _2q2 = 2.0f * q2;\n            float _2q3 = 2.0f * q3;\n            float _2q4 = 2.0f * q4;\n//            float _2q1q3 = 2.0f * q1 * q3;\n//            float _2q3q4 = 2.0f * q3 * q4;\n\n            // Normalise accelerometer measurement\n            norm = sqrt(ax * ax + ay * ay + az * az);\n            if (norm == 0.0f) return; // handle NaN\n            norm = 1.0f/norm;\n            ax *= norm;\n            ay *= norm;\n            az *= norm;\n            \n            // Compute the objective function and Jacobian\n            f1 = _2q2 * q4 - _2q1 * q3 - ax;\n            f2 = _2q1 * q2 + _2q3 * q4 - ay;\n            f3 = 1.0f - _2q2 * q2 - _2q3 * q3 - az;\n            J_11or24 = _2q3;\n            J_12or23 = _2q4;\n            J_13or22 = _2q1;\n            J_14or21 = _2q2;\n            J_32 = 2.0f * J_14or21;\n            J_33 = 2.0f * J_11or24;\n          \n            // Compute the gradient (matrix multiplication)\n            hatDot1 = J_14or21 * f2 - J_11or24 * f1;\n            hatDot2 = J_12or23 * f1 + J_13or22 * f2 - J_32 * f3;\n            hatDot3 = J_12or23 * f2 - J_33 *f3 - J_13or22 * f1;\n            hatDot4 = J_14or21 * f1 + J_11or24 * f2;\n            \n            // Normalize the gradient\n            norm = sqrt(hatDot1 * hatDot1 + hatDot2 * hatDot2 + hatDot3 * hatDot3 + hatDot4 * hatDot4);\n            hatDot1 /= norm;\n            hatDot2 /= norm;\n            hatDot3 /= norm;\n            hatDot4 /= norm;\n            \n            // Compute estimated gyroscope biases\n            gerrx = _2q1 * hatDot2 - _2q2 * hatDot1 - _2q3 * hatDot4 + _2q4 * hatDot3;\n            gerry = _2q1 * hatDot3 + _2q2 * hatDot4 - _2q3 * hatDot1 - _2q4 * hatDot2;\n            gerrz = _2q1 * hatDot4 - _2q2 * hatDot3 + _2q3 * hatDot2 - _2q4 * hatDot1;\n            \n            // Compute and remove gyroscope biases\n            gbiasx += gerrx * deltat * zeta;\n            gbiasy += gerry * deltat * zeta;\n            gbiasz += gerrz * deltat * zeta;\n //           gx -= gbiasx;\n //           gy -= gbiasy;\n //           gz -= gbiasz;\n            \n            // Compute the quaternion derivative\n            qDot1 = -_halfq2 * gx - _halfq3 * gy - _halfq4 * gz;\n            qDot2 =  _halfq1 * gx + _halfq3 * gz - _halfq4 * gy;\n            qDot3 =  _halfq1 * gy - _halfq2 * gz + _halfq4 * gx;\n            qDot4 =  _halfq1 * gz + _halfq2 * gy - _halfq3 * gx;\n\n            // Compute then integrate estimated quaternion derivative\n            q1 += (qDot1 -(beta * hatDot1)) * deltat;\n            q2 += (qDot2 -(beta * hatDot2)) * deltat;\n            q3 += (qDot3 -(beta * hatDot3)) * deltat;\n            q4 += (qDot4 -(beta * hatDot4)) * deltat;\n\n            // Normalize the quaternion\n            norm = sqrt(q1 * q1 + q2 * q2 + q3 * q3 + q4 * q4);    // normalise quaternion\n            norm = 1.0f/norm;\n            q[0] = q1 * norm;\n            q[1] = q2 * norm;\n            q[2] = q3 * norm;\n            q[3] = q4 * norm;\n            \n        }\n        \n  \n  };\n#endif\n"
  },
  {
    "path": "STM32F401/Readme.md",
    "content": "I have started to reproduce the motion sensor sketches I wrote for the 3.3 V 8 MHz Pro Mini and the Teensy 3.1 \nfor 6- and 9-axis motion sensors with open-source sensor fusion filters on another ARM family of processors, \nthe STM32M4 Cortex family, namely the STM32F401.\n\nThe STM32F401 cannot be programmed with an Arduino-like language but the mbed compiler makes the translation from Arduino to\nsomething that can run the STM32F401 pretty easy. The mbed compiler is a middle ground between the ease of programming \nan Arduino and the full-blown tool-chain approach to programming modern ARM devices.\n\nMy intent here is to have all of the 6- and 9-axis motion sensors and their sensor fusion algorithms working on the \nSTM32F401. I am designing portable motion sensing and control devices and have pretty much decided that AVR processors \nare not up to the task. I am currently targeting the Teensy 3.1 ARM M4 Cortex device since it is essentially a commodity \navailable at $17 each from OSHPark.com, open-source, and, I believe, amenable to modular re-configuration by addition of \nsmall boards to get me the motion sensing, BLE commo, battery charging, and motor control functions I want in a very small\ntotal package. However, I am exploring the use of the STM32F401 family also since it is inexpensive, as capable if not\nmore so than the Teensy 3.1 ARM processor, and can operate at extremely low power, which is essential for a portable\ndevice.\n\nSo I am on a parallel development path; which one of these ARM solutions wins time will tell...\n"
  },
  {
    "path": "STM32F401/main.cpp",
    "content": "\n/* MPU6050 Basic Example Code\n by: Kris Winer\n date: May 1, 2014\n license: Beerware - Use this code however you'd like. If you \n find it useful you can buy me a beer some time.\n \n Demonstrate  MPU-6050 basic functionality including initialization, accelerometer trimming, sleep mode functionality as well as\n parameterizing the register addresses. Added display functions to allow display to on breadboard monitor. \n No DMP use. We just want to get out the accelerations, temperature, and gyro readings.\n \n SDA and SCL should have external pull-up resistors (to 3.3V).\n 10k resistors worked for me. They should be on the breakout\n board.\n \n Hardware setup:\n MPU6050 Breakout --------- Arduino\n 3.3V --------------------- 3.3V\n SDA ----------------------- A4\n SCL ----------------------- A5\n GND ---------------------- GND\n \n  Note: The MPU6050 is an I2C sensor and uses the Arduino Wire library. \n Because the sensor is not 5V tolerant, we are using a 3.3 V 8 MHz Pro Mini or a 3.3 V Teensy 3.1.\n We have disabled the internal pull-ups used by the Wire library in the Wire.h/twi.c utility file.\n We are also using the 400 kHz fast I2C mode by setting the TWI_FREQ  to 400000L /twi.h utility file.\n */\n \n#include \"mbed.h\"\n#include \"MPU6050.h\"\n#include \"N5110.h\"\n\n// Using NOKIA 5110 monochrome 84 x 48 pixel display\n// pin 9 - Serial clock out (SCLK)\n// pin 8 - Serial data out (DIN)\n// pin 7 - Data/Command select (D/C)\n// pin 5 - LCD chip select (CS)\n// pin 6 - LCD reset (RST)\n//Adafruit_PCD8544 display = Adafruit_PCD8544(9, 8, 7, 5, 6);\n\nfloat sum = 0;\nuint32_t sumCount = 0;\n\n   MPU6050 mpu6050;\n   \n   Timer t;\n\n   Serial pc(USBTX, USBRX); // tx, rx\n\n   //        VCC,   SCE,  RST,  D/C,  MOSI,S CLK, LED\n   N5110 lcd(PA_8, PB_10, PA_9, PA_6, PA_7, PA_5, PC_7);\n        \nint main()\n{\n  pc.baud(9600);  \n\n  //Set up I2C\n  i2c.frequency(400000);  // use fast (400 kHz) I2C   \n  \n  t.start();        \n  \n  lcd.init();\n  lcd.setBrightness(0.05);\n  \n    \n  // Read the WHO_AM_I register, this is a good test of communication\n  uint8_t whoami = mpu6050.readByte(MPU6050_ADDRESS, WHO_AM_I_MPU6050);  // Read WHO_AM_I register for MPU-6050\n  pc.printf(\"I AM 0x%x\\n\\r\", whoami); pc.printf(\"I SHOULD BE 0x68\\n\\r\");\n  \n  if (whoami == 0x68) // WHO_AM_I should always be 0x68\n  {  \n    pc.printf(\"MPU6050 is online...\");\n    wait(1);\n    lcd.clear();\n    lcd.printString(\"MPU6050 OK\", 0, 0);\n\n    \n    mpu6050.MPU6050SelfTest(SelfTest); // Start by performing self test and reporting values\n    pc.printf(\"x-axis self test: acceleration trim within : \"); pc.printf(\"%f\", SelfTest[0]); pc.printf(\"% of factory value \\n\\r\");\n    pc.printf(\"y-axis self test: acceleration trim within : \"); pc.printf(\"%f\", SelfTest[1]); pc.printf(\"% of factory value \\n\\r\");\n    pc.printf(\"z-axis self test: acceleration trim within : \"); pc.printf(\"%f\", SelfTest[2]); pc.printf(\"% of factory value \\n\\r\");\n    pc.printf(\"x-axis self test: gyration trim within : \"); pc.printf(\"%f\", SelfTest[3]); pc.printf(\"% of factory value \\n\\r\");\n    pc.printf(\"y-axis self test: gyration trim within : \"); pc.printf(\"%f\", SelfTest[4]); pc.printf(\"% of factory value \\n\\r\");\n    pc.printf(\"z-axis self test: gyration trim within : \"); pc.printf(\"%f\", SelfTest[5]); pc.printf(\"% of factory value \\n\\r\");\n    wait(1);\n\n    if(SelfTest[0] < 1.0f && SelfTest[1] < 1.0f && SelfTest[2] < 1.0f && SelfTest[3] < 1.0f && SelfTest[4] < 1.0f && SelfTest[5] < 1.0f) \n    {\n    mpu6050.resetMPU6050(); // Reset registers to default in preparation for device calibration\n    mpu6050.calibrateMPU6050(gyroBias, accelBias); // Calibrate gyro and accelerometers, load biases in bias registers  \n    mpu6050.initMPU6050(); pc.printf(\"MPU6050 initialized for active data mode....\\n\\r\"); // Initialize device for active mode read of acclerometer, gyroscope, and temperature\n\n    lcd.clear();\n    lcd.printString(\"MPU6050\", 0, 0);\n    lcd.printString(\"pass self test\", 0, 1);\n    lcd.printString(\"initializing\", 0, 2);  \n    wait(2);\n       }\n    else\n    {\n    pc.printf(\"Device did not the pass self-test!\\n\\r\");\n \n       lcd.clear();\n       lcd.printString(\"MPU6050\", 0, 0);\n       lcd.printString(\"no pass\", 0, 1);\n       lcd.printString(\"self test\", 0, 2);      \n      }\n    }\n    else\n    {\n    pc.printf(\"Could not connect to MPU6050: \\n\\r\");\n    pc.printf(\"%#x \\n\",  whoami);\n \n    lcd.clear();\n    lcd.printString(\"MPU6050\", 0, 0);\n    lcd.printString(\"no connection\", 0, 1);\n    lcd.printString(\"0x\", 0, 2);  lcd.setXYAddress(20, 2); lcd.printChar(whoami);\n \n    while(1) ; // Loop forever if communication doesn't happen\n  }\n\n\n\n while(1) {\n  \n  // If data ready bit set, all data registers have new data\n  if(mpu6050.readByte(MPU6050_ADDRESS, INT_STATUS) & 0x01) {  // check if data ready interrupt\n    mpu6050.readAccelData(accelCount);  // Read the x/y/z adc values\n    mpu6050.getAres();\n    \n    // Now we'll calculate the accleration value into actual g's\n    ax = (float)accelCount[0]*aRes - accelBias[0];  // get actual g value, this depends on scale being set\n    ay = (float)accelCount[1]*aRes - accelBias[1];   \n    az = (float)accelCount[2]*aRes - accelBias[2];  \n   \n    mpu6050.readGyroData(gyroCount);  // Read the x/y/z adc values\n    mpu6050.getGres();\n \n    // Calculate the gyro value into actual degrees per second\n    gyrox = (float)gyroCount[0]*gRes; // - gyroBias[0];  // get actual gyro value, this depends on scale being set\n    gyroy = (float)gyroCount[1]*gRes; // - gyroBias[1];  \n    gyroz = (float)gyroCount[2]*gRes; // - gyroBias[2];   \n\n    tempCount = mpu6050.readTempData();  // Read the x/y/z adc values\n    temperature = (tempCount) / 340. + 36.53; // Temperature in degrees Centigrade\n   }  \n   \n    Now = t.read_us();\n    deltat = (float)((Now - lastUpdate)/1000000.0f) ; // set integration time by time elapsed since last filter update\n    lastUpdate = Now;\n    \n    sum += deltat;\n    sumCount++;\n    \n    if(lastUpdate - firstUpdate > 10000000.0f) {\n     beta = 0.04;  // decrease filter gain after stabilized\n     zeta = 0.015; // increasey bias drift gain after stabilized\n    }\n    \n   // Pass gyro rate as rad/s\n    mpu6050.MadgwickQuaternionUpdate(ax, ay, az, gyrox*PI/180.0f, gyroy*PI/180.0f, gyroz*PI/180.0f);\n\n    // Serial print and/or display at 0.5 s rate independent of data rates\n    delt_t = t.read_ms() - count;\n    if (delt_t > 500) { // update LCD once per half-second independent of read rate\n\n    pc.printf(\"ax = %f\", 1000*ax); \n    pc.printf(\" ay = %f\", 1000*ay); \n    pc.printf(\" az = %f  mg\\n\\r\", 1000*az); \n\n    pc.printf(\"gyrox = %f\", gyrox); \n    pc.printf(\" gyroy = %f\", gyroy); \n    pc.printf(\" gyroz = %f  deg/s\\n\\r\", gyroz); \n    \n    pc.printf(\" temperature = %f  C\\n\\r\", temperature); \n    \n    pc.printf(\"q0 = %f\\n\\r\", q[0]);\n    pc.printf(\"q1 = %f\\n\\r\", q[1]);\n    pc.printf(\"q2 = %f\\n\\r\", q[2]);\n    pc.printf(\"q3 = %f\\n\\r\", q[3]);      \n    \n    lcd.clear();\n    lcd.printString(\"MPU6050\", 0, 0);\n    lcd.printString(\"x   y   z\", 0, 1);\n    lcd.setXYAddress(0, 2); lcd.printChar((char)(1000*ax));\n    lcd.setXYAddress(20, 2); lcd.printChar((char)(1000*ay));\n    lcd.setXYAddress(40, 2); lcd.printChar((char)(1000*az)); lcd.printString(\"mg\", 66, 2);\n    \n    \n  // Define output variables from updated quaternion---these are Tait-Bryan angles, commonly used in aircraft orientation.\n  // In this coordinate system, the positive z-axis is down toward Earth. \n  // Yaw is the angle between Sensor x-axis and Earth magnetic North (or true North if corrected for local declination, looking down on the sensor positive yaw is counterclockwise.\n  // Pitch is angle between sensor x-axis and Earth ground plane, toward the Earth is positive, up toward the sky is negative.\n  // Roll is angle between sensor y-axis and Earth ground plane, y-axis up is positive roll.\n  // These arise from the definition of the homogeneous rotation matrix constructed from quaternions.\n  // Tait-Bryan angles as well as Euler angles are non-commutative; that is, the get the correct orientation the rotations must be\n  // applied in the correct order which for this configuration is yaw, pitch, and then roll.\n  // For more see http://en.wikipedia.org/wiki/Conversion_between_quaternions_and_Euler_angles which has additional links.\n    yaw   = atan2(2.0f * (q[1] * q[2] + q[0] * q[3]), q[0] * q[0] + q[1] * q[1] - q[2] * q[2] - q[3] * q[3]);   \n    pitch = -asin(2.0f * (q[1] * q[3] - q[0] * q[2]));\n    roll  = atan2(2.0f * (q[0] * q[1] + q[2] * q[3]), q[0] * q[0] - q[1] * q[1] - q[2] * q[2] + q[3] * q[3]);\n    pitch *= 180.0f / PI;\n    yaw   *= 180.0f / PI; \n    roll  *= 180.0f / PI;\n\n//    pc.printf(\"Yaw, Pitch, Roll: \\n\\r\");\n//    pc.printf(\"%f\", yaw);\n//    pc.printf(\", \");\n//    pc.printf(\"%f\", pitch);\n//    pc.printf(\", \");\n//    pc.printf(\"%f\\n\\r\", roll);\n//    pc.printf(\"average rate = \"); pc.printf(\"%f\", (sumCount/sum)); pc.printf(\" Hz\\n\\r\");\n\n     pc.printf(\"Yaw, Pitch, Roll: %f %f %f\\n\\r\", yaw, pitch, roll);\n     pc.printf(\"average rate = %f\\n\\r\", (float) sumCount/sum);\n \n    myled= !myled;\n    count = t.read_ms(); \n    sum = 0;\n    sumCount = 0; \n}\n}\n \n }\n"
  },
  {
    "path": "quaternionFilter.ino",
    "content": "// Implementation of Sebastian Madgwick's \"...efficient orientation filter for... inertial/magnetic sensor arrays\"\n// (see http://www.x-io.co.uk/category/open-source/ for examples and more details)\n// which fuses acceleration and rotation rate to produce a quaternion-based estimate of relative\n// device orientation -- which can be converted to yaw, pitch, and roll. Useful for stabilizing quadcopters, etc.\n// The performance of the orientation filter is at least as good as conventional Kalman-based filtering algorithms\n// but is much less computationally intensive---it can be performed on a 3.3 V Pro Mini operating at 8 MHz!\n        void MadgwickQuaternionUpdate(float ax, float ay, float az, float gyrox, float gyroy, float gyroz)\n        {\n            float q1 = q[0], q2 = q[1], q3 = q[2], q4 = q[3];         // short name local variable for readability\n            float norm;                                               // vector norm\n            float f1, f2, f3;                                         // objetive funcyion elements\n            float J_11or24, J_12or23, J_13or22, J_14or21, J_32, J_33; // objective function Jacobian elements\n            float qDot1, qDot2, qDot3, qDot4;\n            float hatDot1, hatDot2, hatDot3, hatDot4;\n            float gerrx, gerry, gerrz, gbiasx, gbiasy, gbiasz;        // gyro bias error\n\n            // Auxiliary variables to avoid repeated arithmetic\n            float _halfq1 = 0.5f * q1;\n            float _halfq2 = 0.5f * q2;\n            float _halfq3 = 0.5f * q3;\n            float _halfq4 = 0.5f * q4;\n            float _2q1 = 2.0f * q1;\n            float _2q2 = 2.0f * q2;\n            float _2q3 = 2.0f * q3;\n            float _2q4 = 2.0f * q4;\n            float _2q1q3 = 2.0f * q1 * q3;\n            float _2q3q4 = 2.0f * q3 * q4;\n\n            // Normalise accelerometer measurement\n            norm = sqrt(ax * ax + ay * ay + az * az);\n            if (norm == 0.0f) return; // handle NaN\n            norm = 1.0f/norm;\n            ax *= norm;\n            ay *= norm;\n            az *= norm;\n            \n            // Compute the objective function and Jacobian\n            f1 = _2q2 * q4 - _2q1 * q3 - ax;\n            f2 = _2q1 * q2 + _2q3 * q4 - ay;\n            f3 = 1.0f - _2q2 * q2 - _2q3 * q3 - az;\n            J_11or24 = _2q3;\n            J_12or23 = _2q4;\n            J_13or22 = _2q1;\n            J_14or21 = _2q2;\n            J_32 = 2.0f * J_14or21;\n            J_33 = 2.0f * J_11or24;\n          \n            // Compute the gradient (matrix multiplication)\n            hatDot1 = J_14or21 * f2 - J_11or24 * f1;\n            hatDot2 = J_12or23 * f1 + J_13or22 * f2 - J_32 * f3;\n            hatDot3 = J_12or23 * f2 - J_33 *f3 - J_13or22 * f1;\n            hatDot4 = J_14or21 * f1 + J_11or24 * f2;\n            \n            // Normalize the gradient\n            norm = sqrt(hatDot1 * hatDot1 + hatDot2 * hatDot2 + hatDot3 * hatDot3 + hatDot4 * hatDot4);\n            hatDot1 /= norm;\n            hatDot2 /= norm;\n            hatDot3 /= norm;\n            hatDot4 /= norm;\n            \n            // Compute estimated gyroscope biases\n            gerrx = _2q1 * hatDot2 - _2q2 * hatDot1 - _2q3 * hatDot4 + _2q4 * hatDot3;\n            gerry = _2q1 * hatDot3 + _2q2 * hatDot4 - _2q3 * hatDot1 - _2q4 * hatDot2;\n            gerrz = _2q1 * hatDot4 - _2q2 * hatDot3 + _2q3 * hatDot2 - _2q4 * hatDot1;\n            \n            // Compute and remove gyroscope biases\n            gbiasx += gerrx * deltat * zeta;\n            gbiasy += gerry * deltat * zeta;\n            gbiasz += gerrz * deltat * zeta;\n            gyrox -= gbiasx;\n            gyroy -= gbiasy;\n            gyroz -= gbiasz;\n            \n            // Compute the quaternion derivative\n            qDot1 = -_halfq2 * gyrox - _halfq3 * gyroy - _halfq4 * gyroz;\n            qDot2 =  _halfq1 * gyrox + _halfq3 * gyroz - _halfq4 * gyroy;\n            qDot3 =  _halfq1 * gyroy - _halfq2 * gyroz + _halfq4 * gyrox;\n            qDot4 =  _halfq1 * gyroz + _halfq2 * gyroy - _halfq3 * gyrox;\n\n            // Compute then integrate estimated quaternion derivative\n            q1 += (qDot1 -(beta * hatDot1)) * deltat;\n            q2 += (qDot2 -(beta * hatDot2)) * deltat;\n            q3 += (qDot3 -(beta * hatDot3)) * deltat;\n            q4 += (qDot4 -(beta * hatDot4)) * deltat;\n\n            // Normalize the quaternion\n            norm = sqrt(q1 * q1 + q2 * q2 + q3 * q3 + q4 * q4);    // normalise quaternion\n            norm = 1.0f/norm;\n            q[0] = q1 * norm;\n            q[1] = q2 * norm;\n            q[2] = q3 * norm;\n            q[3] = q4 * norm;\n        }\n"
  }
]